Danfoss AKD 5001 Скачать руководство пользователя страница 55

Страница: 55 / 124

AKD 5000

■

PID for process control

Feedback

The feedback signal must be connected to a terminal

on the frequency converter. Use the list below to

decide which terminal is to be used and which

parameters are to be programmed.

Feedback type

Terminal

Parameters

Pulse

307

Voltage

308, 309, 310

Current

314, 315, 316

Furthermore, the minimum and maximum feedback

(parameters 414 and 415) must be set to a value in

the process unit that corresponds to the minimum

and maximum value on the terminal.

Select process unit in parameter 416.

Reference

A minimum and a maximum reference can be set (204

and 205), which limit the sum of all references. The

reference range cannot exceed the feedback range.

If one or several setpoint references are required,

the simplest way is to set such reference directly

in parameters 215 to 218. Select between the

preset references by connecting terminals 16, 17,

29, 32 and/or 33 to terminal 12. Which terminals

that are used depends on the choice made in the

parameters of the various terminals (parameters

300, 301, 305, 306 and/or 307). Use the table

below when selecting preset references.

Preset ref. msb

Preset ref. lsb

Preset ref. 1
(par. 215)

Preset ref. 2
(par. 216)

Preset ref. 3
(par. 217)

Preset ref. 4
(par. 218)

If an external reference is required, this can either

be an analogue or a pulse reference. If current

is used as a feedback signal, only voltage can

be used as an analogue reference. Use the

following list to decide which terminal to use and

which parameters to program.

Reference type

Terminal

Parameters

Pulse

17 or 29

301 or 305

Voltage

53 or 54

308, 309, 310 or
311, 312, 313

Current

314, 315, 316

Relative references can be programmed. A relative

reference is a percentage value (Y) of the sum of

the external references (X). This percentage value

is added to the sum of the external references,

which produces the active reference (X + XY). See

section

Handling of multi references.

If relative references are to be used, parameter 214 is to

be set to

Relative

[1]. This makes the preset references

relative. Furthermore,

Relative reference

[4] can be

programmed on terminal 54 and/or 60. If an external

relative reference is selected, the signal on the input will

be a percentage value of the full range of the terminal.

The relative references are added with signs.

NB!:

Terminals that are not in use should preferably

be set to

No function

[0].

Inverse control

If the drive has to react with increasing speed on

and increasing feedback,

Inverse

must be selected in

parameter 437. Normal control means that the motor

speed decreases when the feedback signal increases.

Anti Windup

The process controller comes with the anti windup

function in active position. This function ensures

that when either a frequency limit or a torque limit

is reached, the integrator will be set to a gain that

corresponds to the actual frequency. This avoids

integrating on an error that cannot in any case be

compensated for by means of a speed change.

Start-up conditions

In some applications, optimum setting of the process

controller will mean that it takes an excessive time

for the desired process value to be reached. In

such applications it might be an advantage to fix a

motor frequency to which the frequency converter is

to bring the motor before the process controller is

activated. This is done by programming a

Process

PID

start frequency in parameter 439.

Lowpass filter

If there are oscillations of the current/voltage feedback

signal, these can be dampened by means of a lowpass

filter. Set a suitable lowpass filter time constant. This

time constant represents the limitfrequency of the

ripples occurring on the feedback signal. If the lowpass

filter has been set to 0.1s, the limit frequency will be 10

RAD/sec., corresponding to (10/2 x

) = 1.6 Hz. This

will mean that all currents/voltages that vary by more

than 1.6 oscillations per second will be removed by

the filter. In other words, control will only be carried

out on a feedback signal that varies by a frequency of

MG.50.R3.02 -

Содержание AKD 5001





























































































































Результаты поиска

Содержание AKD 5001

Отзывы:

Похожие инструкции для AKD 5001

Бренды по названию

Популярные бренды

Danfoss AKD 5001, Руководство пользователя

Результаты поиска

Содержание AKD 5001

Отзывы:

Похожие инструкции для AKD 5001

Бренды по названию

Популярные бренды