Daktronics GEN VI RADIO P1110, Руководство по установке

Страница: 23 / 34

INSTALLATION STEPS:
1. TURN POWER OFF TO THE SCOREBOARD.
2. LOCATE THE PANEL ON THE SCOREBOARD THAT HAS THE DRIVER TRAY
BEHIND IT AND OPEN. ATTACH SNAP TRACK TO BACKSHEET WITHIN 1' OF
DRIVER USING THE DOUBLE SIDED TAPE PRE-INSTALLED ON BACK OF SNAP
TRACK. SNAP WIRE/RADIO SWITCH CARD INTO SNAP TRACK JUST
INSTALLED.
3. CONNECT POWER TO RADIO/WIRE SWITCH CARD.
3.1 LOCATE 5 PIN PLUG (P45) THAT CONNECTS THE RADIO
RECEIVER TO THE DRIVER TRAY.
3.2 DISCONNECT THE RADIO RECEIVER.
3.3 CONNECT POWER HARNESS INCLUDED WITH RADIO/WIRE
SWITCH KIT TO THE 5 PIN JACK (J45) ON THE DRIVER
TRAY.
3.4 CONNECT THE 2 PIN END OF HARNESS JUST INSTALLED
TO THE RADIO/WIRE SWITCH CARD J1 (POWER).
4. REROUTE SIGNAL INTO THE WIRE/RADIO SWITCH CARD JUST INSTALLED.
4.1 USE A SCREWDRIVER TO LOOSEN THE SCREWS ON
THE SIGNAL TERMINAL BLOCK ON THE DRIVER TRAY,
TB31-1&2 (RED AND BLK WIRES). THESE ARE THE
WIRES THAT COME FROM THE 1
4
" PHONE JACK ON THE
OUTSIDE OF THE SCOREBOARD.
4.2 MOVE WIRES JUST REMOVED FROM THE DRIVER TRAY
TO THE SIGNAL IN TERMINAL BLOCK (TB1) ON THE
RADIO/WIRE SWITCH CARD. RED IS CONNECT TO +
AND BLACK IS CONNECTED TO -.
4.3 INSTALL THE JUMPER WIRE INCLUDED WITH THE
RADIO/WIRE SWITCH KIT FROM THE SIGNAL OUT
TERMINAL BLOCK (TB2) ON THE RADIO/WIRE SWITCH
CARD (RED +, BLACK -) TO THE DRIVER TRAY TB31
(RED TB31-1, BLACK TB31-2).
5. CONNECT 5 PIN PLUG (P45) FROM RADIO RECEIVER TO J2 (RADIO) ON THE
WIRE/RADIO SWITCH CARD.
6. DOUBLE CHECK ALL CONNECTIONS TO BE SURE SYSTEM IS CONNECTED
PROPERLY AND THAT ALL CONNECTIONS ARE TIGHT.
7. CLOSE SCOREBOARD PANEL.
8. TURN POWER BACK ON TO SCOREBOARD AND TEST.
J2 J4
J17
J1 J3
J6 J8 J12 J10 J14
J5 J7 J11 J9 J13
J20
J16
J18
J19
J15
HAZARDOUS VOLTAGE
AT EXPOSED TERMINALS
DISCONNECT POWER
BEFORE SERVICING
TRANSFORMER
WHT BLU
ORG
GRY
BRN
PNK
TAN
6
7
8
9
10 5
4
1
2
3
SIGNAL
5
TAN
4
PNK
3
VIO
2
BLK RED
1
RADIO/WIRE
SWITCH
STEP 2
SWITCH INSTALLAION
RE-ROUTE SIGNAL
STEP 4
SWITCH
RADIO/WIRE
1
RED BLK
2
VIO
3
PNK
4
TAN
5
SIGNAL
3
2
1
4
5 10
9
8
7
6
TAN
PNK
BRN
GRY
ORG
BLU WHT
TRANSFORMER
BEFORE SERVICING
DISCONNECT POWER
AT EXPOSED TERMINALS
HAZARDOUS VOLTAGE
J2 J4
J17
J1 J3
J6 J8 J12 J10 J14
J5 J7 J11 J9 J13
J20
J16
J18
J19
J15
SIGNAL IN
SIGNAL OUT
INCOMING SIGNAL
WIRES FROM 1/4"
PHONE JACK
RED BLK
BLK RED
BLK
RED
STEP 6
CHECK CONNECTIONS
GRY
RADIO
PWR/SIG
CONNECT
BLK
RED
GRY
WHT
5
4
3
2
1
J45
VIO
P42
J31
SIGNAL IN
BLK
RED
LED DRIVER/TRANSFORMER/TRAY ASSEMBLY
WHT
BRN
PNK
ORN
TAN
BLU
TAN
PNK
BLK
RED
T1
DRIVER
LED
TB31
5
4
3
2
1
10
8
6
1
2
4
5
16V AC SECONDARY
SIG IN +
SIG IN -
SIG OUT -
SIG OUT +
16V AC IN
16V AC IN
10
11
12 12
11
10
1
2
3
4
5
6
7
8
9 9
8
7
6
5
4
3
2
1
J17 P17
1
2
3
4
+
-
NC
SIGNAL IN
SIGNAL OUT
NC
-
+
J2 RADIO
1
2
3
4
5
2
1
POWER
J1
5
4
3
2
1
TO RADIO
RECEIVER
1
2
WHT
GRY
RADIO/WIRE SWITCH
0P-1110-0013
1
2
3
4
5
P45
GRY
WHT
RED
BLK
RED BLK
BLK
RED
TB1
TB2
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS
DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT
REPRODUCE BY ANY MEANS WITHOUT THE EXPRESSED
WRITTEN CONSENT OF DAKTRONICS, INC.
COPYRIGHT 2012 DAKTRONICS, INC.
DAKTRONICS, INC.
BH
DRAWN: DATE:
SHEET JOB NO: REV
STANDARD INDOOR LED SCOREBOARDS
INSTALL DETAILS: INDOOR RADIO/WIRE SWITCH
CBRECZI 03 JUN 02
1152 E 01 B
1=1
168045
01
DATE: REV BY:
01 13 NOV 12
SMB
ADJUSTED WIRE CONNECTIONS TO SECONDARY SIDE OF 16VAC
XNSFMR PER EC-8255.