manualshive.com logo in svg

Daikin Trailblazer AGZ030E-070E, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Daikin Trailblazer AGZ030E-070E Скачать руководство пользователя страница 40

IOM 1207-6 • TRAILBLAZER

®

 MODEL AGZ CHILLERS 

40 www.DaikinApplied.com

Dimensions and Weights - Remote Evaporator Units

Figure 42: Remote Evap Condensing Unit - 14 Fan; AGZ226E-AGZ241E     

2235 88.0

DIMENSION DOES NOT

INCLUDE LIFTING BRACKETS

165 6.5

175 6.9

213 8.4

2355 92.7

2506 98.6

292 11.5

64 2.5

64 2.5

X

Y

CONTROL

BOX

[22]

.875 KNOCKOUTS

FIELD CONTROL CONNECTIONS

1

609 24.0

2207 86.9

1375 54.1

2207 86.9

1919 75.5

8317 327.4

37 1.5

548 21.6

184 7.2

229 9.0

127 5.0

51 2.0

305 12.0

22 .875

 KNOCKOUTS

POWER ENTRY POINTS

ARE ON OPPOSITE

SIDE OF CONTROL BOX

Z

80 3.1

L1 L2

L3 L4

L5 L6

L7 L8

1

SUCTION

HOT GAS

LIQUID

2743 108.0

1114 43.8

2433 95.8

315 12.4

52 2.0

52 2.0

1711 67.4

19 .75

QTY 8

5568 219.2

 TYP.

5687 223.9

 TYP.

113 4.4

353 13.9

113 4.4

828 32.6

COMPRESSORS CIRCUIT #1

COMPRESSORS CIRCUIT #2

M1 - M8, ISOLATOR MOUNTING HOLE LOCATIONS ON BOTTOM SURFACE OF 

UNIT BASE.

M1

L1

M3

L3

M5

L5

L7

M7

M2

L2

M4

L4

M6

L6

L8

M8

LIQUID & HOT

GAS CIR. 2

SUCTION CIR. 2

SUCTION CIR. 1

LIQUID & HOT

GAS CIR. 1

NOTE:  LIFTING WEIGHTS ARE BASED ON UNIT SHIPPING WEIGHTS. MOUNTING  WEIGHTS ARE BASED ON UNIT OPERATING WEIGHT WITH REFRIGERANT  INCLUDED. SHIPPING AND OPERATING WEIGHTS DO NOT INCLUDE THE  WEIGHTS OF ANY OPTIONS OR ACCESSORIES.

[22]

.875 KNOCKOUTS

POWER ENTRY POINTS FRONT AND RIGHT SIDE

TOP VIEW WITH COILS AND FANS REMOVED

NOTE:

IT IS RECOMMENDED THAT THE SIDE LOCATIONS BE USED
1.

FOR POWER ENTRY WIRE SIZES LARGER THAN 350 MCM.

L1 - L8 LIFTING

LOCATIONS

334547145

UNIT 

REFRIGERANT 

CONNECTIONS

 

MODEL 

SUCT. 

O.D. 

IN.

 

 

 

MM

 

AGZ226E

 

3.13 

79.5 

AGZ241E

 

LIQ. O.D.  IN.

 

 

 

MM 

1.38 

35.1 

HGBP 

O.D.

 

IN. 

 

 

M

M 

1.13 

28.7 

UNIT  MODEL 

AGZ226E  AGZ241E 

CG 

LOCATION 

X

 

Y

 

Z

 

IN. 

MM

 

IN.

 

MM

 

IN. 

MM

 

43.7 

1110 

44.8 

1138 

111.3 

2827 

43.8 

1113 

44.7 

1135 

110.

2 

2799 

UNIT  MODEL 

AGZ226E  AGZ241E 

SHI

P 

WEIGHT 

OP

ER

WEI

GH

T 

L1 

L2 

LBS 

KG 

LBS 

KG 

LBS 

I 

KG 

LBS 

KG

 

7996

 

3627

 

8424

 

3821

 

1451 I 658 

1433 

650 

8075 

3663 

8519 

3864 

1481 I 672 

1469 

666 

LIFTING 

(SHIPPING) 

WEIGHT 

BY 

CORNER 

L3 

L4 

L5 

L6 

L7 

LB 

M1 

M2 

LBS 

I 

KG 

LBS 

I 

KG 

LBS 

I 

KG

 

LBS 

I 

KG 

LBS 

I 

KG

 

LBS 

I 

KG

 

LBS 

I 

KG 

LBS 

I 

KG

 

1111 I 504 

1098 

I 

498 

900

 I 

408 

889 

I 

403 

560 I 254 

553

 I 

251 

1413 I 641 

1396 

I 

633 

1125 I 510 

1115 I 506 

903

 

I 

410 

895 

I 

406 

546 I 248 

541

 

I 

245 

1444 I 655 

1432 I 650 

MOUNTING 

(OP

ER

AT

ING

) WEIGHT 

M

3 

M4 

LBS 

I 

KG 

LBS 

I 

KG 

1133 I 514 

1119 

I 

508 

1141 I 520 

1137 I 516 

M

5 

M

6 

LBS 

I 

KG

 

LBS 

I 

KG

 

1004 

I 

455

 

992 

I 

450 

10111459 

1003 

I 

455 

M7 

LBS 

I 

KG

 

688 I 312  676 I 301 

MB 

LBS 

I 

KG 

680 

I 

30

8 

670 

I 

30

4 

Содержание Trailblazer AGZ030E-070E





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды