manualshive.com logo in svg

Daikin Trailblazer AGZ030E-070E, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Daikin Trailblazer AGZ030E-070E Скачать руководство пользователя страница 28

IOM 1207-6 • TRAILBLAZER

®

 MODEL AGZ CHILLERS 

28 www.DaikinApplied.com

Remote Evaporators

Figure 29: Remote Evaporator Piping Models 030-070         

Figure 30: Remote Evaporator Piping Models 075-241      

SUCTION

CIR. #2

SUCTION

CIR. #1

LIQUID

CIR. #1

LIQUID

CIR. #2

ENTERING WATER 

TEMP SENSOR

LOCATION

STAINLESS STEEL

PIPE PLUG

BRAZE CONNECTIONS ON EVAP ARE STAINLESS STEEL,

SO FIELD MUST USE MIN 45% SILVER BRAZE ROD.

■-SIGHT GLASS (INCLUDED IN KIT)

■-FILTER DRIER, CORES, CLAMP & GASKET KITS (ALL INCLUDED IN KIT)

■-ELECTRIC EXPANSION VALVE AND CABLE (INCLUDED IN KIT)

LIQUID CIRCUIT #1

LIQUID CIRCUIT #2

WATER

OUTLET

WATER INLET

WATER STRAINER 

REQUIRED

(SEPARATE KIT OR

FIELD SUPPLIED)

SCHRADER FITTINGS (FIELD SUPPLIED)

OPTIONAL HOT GAS BYPASS LINE MUST ENTER FROM VERTICAL POSITION AS SHOWN.

AGZ030-070E 4 FAN UNITS, WITH EXV

■ - DENOTES PARTS INCLUDED IN

REMOTE EVAP. SPECIALTIES KIT

CIRCUIT #1 

COMPRESSORS

CIRCUIT #2 

COMPRESSORS

LIQUID LINE 

SHUTOFF VALVE

CIRCUIT #1

■-BALL VALVES WITH SCHRADER VALVES TO BE LOCATED

CLOSEST TO THE FILTER DRIER (INCLUDED IN KIT)

■-LIQUID LINE SOLENOID VALVE (INCLUDED IN KIT)

OPTION

HOT GAS BYPASS

CIRCUIT #1

OPTION

HOT GAS BYPASS

CIRCUIT #2

■-BALL VALVES WITH

SCHRADER VALVES TO BE 

LOCATED CLOSEST TO THE 

FILTER DRIER (INCLUDED IN KIT)

■-HOT GAS CHECK VALVES (INCLUDED IN KIT)

HGBP PIPING SLOPE TO EVAP.

1 INCH DOWN PER

10 FEET DISTANCE

4

■-ELECTRIC EXPANSION VALVE CABLES

(INCLUDED IN KIT)

RUN EXPANSION VALVE CABLE INTO BACK

OF CONTROL BOX AND CONNECT TO:

LIQUID LINE 

SHUTOFF VALVE

CIRCUIT #2

STAINLESS STEEL SENSOR

WELL FOR LEAVING 

WATER TEMP. SENSOR

LEAVING WATER

PIPE ASSEMBLY

VALVE

CORE

SUCTION

CIR. #2

SUCTION

CIR. #1

■-SUCTION PRESSURE

TRANSDUCERS, SCHRADER

FITTINGS WITH CORES

(INCLUDED IN KIT)

■-SUCTION TEMP. SENSOR TUBES

(INCLUDED IN KIT)

THE SUCTION TEMPERATURE SENSORS 

AND TRANSDUCERS MUST BE LOCATED 

AT THE EVAPORATOR AS SHOWN.

■-CHARGING VALVES

(INCLUDED IN KIT)

NOTES:

FOR FILTER DRIER SERVICE:

1.

ISOLATE DRIER BY CLOSING LIQUID LINE BALL

VALVES LOCATED ON BOTH SIDES OF DRIER.

LIQUID LINE SOLENOID & FILTER DRIER MUST BE

2.

LOCATED AT REMOTE EVAPORATOR.

SUPPORT FIELD PIPING AS REQUIRED.

3.

USED ONLY WHEN EVAPORATOR IS HIGHER

4.

THAN THE CONDENSING UNIT.

LIQUID LINE 

SOLENOID VALVE HARNESSES

RUN SOLENOID VALVE HARNESSES INTO 

BACK OF CONTROL BOX AND CONNECT TO:

CIR. #1: (E.E.X.V.1)

WHT TO M1+ ;  BLK TO M1-

RED TO M2+ ; GRN TO M2-

CIR. #2: (E.E.X.V.2)

WHT TO M1+ ; BLK TO M1-

RED TO M2+ ; GRN TO M2-

CIR. #1: RED #1 TO TB2-91

WHT #2 TO TB1-29

CIR. #2: RED #1 TO TB2-92

WHT #2 TO TB1-29

WIRING AND CONDUIT ARE FIELD 

SUPPLIED. 

■-MOV SOLENOID CONNECTORS

ARE INCLUDED IN KIT.

334705191

Содержание Trailblazer AGZ030E-070E





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды