Daikin Trailblazer AGZ030E-070E Скачать руководство пользователя страница 37

Страница: 37 / 148

Dimensions and Weights - Remote Evaporator Units

www.DaikinApplied.com 37

IOM 1207-6 • TRAILBLAZER

MODEL AGZ CHILLERS

Figure 39: Remote Evap Condensing Unit - 10 Fan; AGZ140E-AGZ161E

37 1.5

609 24.0

1919 75.5

6025 237.2

483 19.0

173 6.8

226 8.9

22 .875

KNOCKOUTS

POWER ENTRY KNOCKOUTS ARE ON THE OPPOSITE SIDE OF THE CONTROL BOX

51 2.0

80 3.1

305 12.0

127 5.0

L1 L2

L3 L4

L1 - L4 LIFTING

LOCATIONS

SUCTION

HOT GAS

LIQUID

2506 98.6

2355 92.7

213 8.4

175 6.9

165 6.5

2235 88.0

DIMENSION DOES NOT INCLUDE

LIFTING BRACKETS

292 11.5

64 2.5

22 .875

KNOCKOUTS

FIELD CONTROL CONNECTIONS

QTY. 3

CONTROL BOX

[22]

.875

POWER ENTRY KNOCKOUTS FRONT OR RIGHT SIDE

52 2.0

315 12.4

2433 95.8

1564 61.6

1711 67.4

52 2.0

19 .750

QTY. 6

204 8.0

188 7.4

827 32.6

3391 133.5

TYP.

M1 - M6, ISOLATOR MOUNTING HOLE LOCATIONS ON BOTTOM SURFACE OF

UNIT BASE.

TOP VIEW WITH COILS AND FANS REMOVED

COMPR. CIR. 1

COMPR. CIR. 2

SUCTION CIR. 2

LIQUID & HOT GAS CIR. 2

SUCTION CIR. 1

LIQUID & HOT GAS CIR. 1

NOTE: LIFTING WEIGHTS ARE BASED ON UNIT SHIPPING WEIGHTS.

MOUNTING WEIGHTS ARE BASED ON

UNIT OPERATING WEIGHT WITH REFRIGERANT INCLUDED.

SHIPPING AND OPERATING WEIGHTS

DO NOT INCLUDE THE WEIGHTS OF ANY OPTIONS OR

ACCESSORIES.

NOTE:

IT IS RECOMMENDED THAT THE SIDE LOCATIONS BE USED
1.

FOR POWER ENTRY WIRE SIZES LARGER THAN 350 MCM.

334547135

SHIP

WEIGHT

OPER. WEIGHT

LIFTING

(SHIPPING)

WEIGHT

CORNER

MOUNTING

(OPERATING)

WEIGHT

UNIT

MODEL

LBS

5775

2619

6079

2757

1676

760

771

1192

541

1208

548

1322

600

1340

608

964

437

977

443

733

5802

2632

6106

2770

1680

762

169

768

1209

548

1219

553

1323

600

1334

605

972

441

980

445

746

AGZ161E

582

2644

6141

2785

1700

771

542

1211

549

1343

609

1362

618

972

441

986

447

734

LBS

332

744

337

338

752

341

333

744

337

UNIT MODEL

AGZ140E AG

Z15

AGZ1

IN.

44.3

1125

44.2

44.3

1125

LOCATION

IN.

44.6

1133

81.2

2062

44.5

1130

81.6

2073

44.5

1130

80.8

2052

UNIT

MODEL

AGZ140E

AGZ150E

AGZ161E

REFRIGERANT

CONNECTIONS

SUCT

. O.D.

LIQ.

O.D.

HGBP

O.D.

IN.

2.63

66.8

1.13

28.

1.13

28.

Содержание Trailblazer AGZ030E-070E





















































































































































Результаты поиска

Содержание Trailblazer AGZ030E-070E

Отзывы:

Бренды по названию

Популярные бренды

Daikin Trailblazer AGZ030E-070E, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Trailblazer AGZ030E-070E

Отзывы:

Бренды по названию

Популярные бренды