Daikin Trailblazer AGZ030E-070E Скачать руководство пользователя страница 35

Страница: 35 / 148

Dimensions and Weights - Remote Evaporator Units

www.DaikinApplied.com 35

IOM 1207-6 • TRAILBLAZER

MODEL AGZ CHILLERS

Figure 37: Remote Evap Condensing Unit - 6 Fan; AGZ075E-AGZ100E

916 36.1

609 24.0

3733 147.0

37 1.5

226 8.9

168 6.6

489 19.3

22 .875

KNOCKOUTS

POWER ENTRY KNOCKOUTS ARE ON THE OPPOSITE SIDE OF THE CONTROL BOX

305 12.0

80 3.1

51 2.0

127 5.0

L1 L2

L3 L4

SUCTION

HOT GAS

LIQUID

165 6.5

2235 88.0

DIMENSION DOES NOT INCLUDE

LIFTING BRACKETS

175 6.9

213 8.4

2355 92.7

2506 98.6

292 11.5

64 2.5

22 .875

KNOCKOUTS

FIELD CONTROL CONNECTIONS

QTY. 3

CONTROL

BOX

[22]

.875 POWER ENTRY

KNOCKOUTS FRONT OR RIGHT SIDE

315 12.4

984 38.7

2433 95.8

52 2.0

19 .750

QTY. 4

52 2.0

1453 57.2

TYP.

825 32.5

189 7.5

206 8.1

190 7.5

M1 - M4, ISOLATOR MOUNTING HOLE LOCATIONS ON BOTTOM SURFACE OF

UNIT BASE.

COMPR. CIRCUIT 1

COMPR. CIRCUIT 2

TOP VIEW WITH COILS AND FANS REMOVED

SUCTION CIR. 2

SUCTION CIR. 1

LIQUID & HOT GAS CIR. 1

LIQUID & HOT GAS CIR. 2

L1 - L4, LIFTING

LOCATIONS

NOTE: LIFTING WEIGHTS ARE BASED ON UNIT SHIPPING WEIGHTS. MOUNTING WEIGHTS ARE BASED ON UNIT OPERATING WEIGHT

WITH REFRIGERANT INCLUDED.

SHIPPING AND OPERATING WEIGHTS DO NOT INCLUDE THE W

EIGHTS OF ANY OPTIONS OR ACCESSORIES.

NOTES:

IT IS RECOMMENDED THAT THE SIDE LOCATIONS BE USED
1.

FOR POWER ENTRY WIRE SIZES LARGER THAN 350 MCM.

334547115

Содержание Trailblazer AGZ030E-070E





















































































































































Результаты поиска

Содержание Trailblazer AGZ030E-070E

Отзывы:

Бренды по названию

Популярные бренды

Daikin Trailblazer AGZ030E-070E, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Trailblazer AGZ030E-070E

Отзывы:

Бренды по названию

Популярные бренды