manualshive.com logo in svg

Daikin FHQ100BUV3B, Руководство по обслуживанию, Страница: 175 / 390

Поделиться
Скачать
Daikin FHQ100BUV3B Скачать руководство пользователя страница 175

ESIE05-04

Troubleshooting

Part 3 – Troubleshooting

3–13

3

3

4

5

1

Troubleshooting

Caution

Be sure to turn off power switch before connect or disconnect connector, or parts damage may be 
occurred.

Measure the temperature of 
suction air and supply air.
Temperature difference = 
Suction air temp. – Supply air 
temp.

Wait for a while.
No abnormality

No abnormality

Additional unit installation 
should be considered

After vacuum drying, charge 
correct amount of refrigerant.

Check each item

Check each item

Check each item

Temperature

difference for heating

should be between 14

and 30˚C.

Is the unit

in defrost mode?

Is the operation

current less than specified 

level?

Does the

heat load increase after

installation of the

unit?

YES

YES

YES

YES

YES

YES

∗

 Incorrect selection of model

∗

 Affection of sunlight

∗ 

Affection of excessive fresh 
air into room

Gas shortage possibly 
generates trouble.

∗

 Clogged air filter 

∗

 Soiled heat exchanger

∗

 Malfunction of indoor fan 

motor (Refer error code “A6”)

∗

 Refrigerant overcharge

∗

 Soiled heat exchanger

∗

 Short circuit of discharge air

∗

 Disturbing item in air flow

∗

 Malfunction of fan motor of 

  outdoor unit

(Refer error code “E7”, “H7”)

∗

 Insufficient compression of 

   compressor

∗

 Insufficient circulation of 

   refrigerant

∗

 Faulty expansion valve

NO

NO

NO

Does indoor
unit air flow 

rate down?

NO

Is the level

of high pressure lower

than normal level?

NO

NO

(S1995)

Содержание FHQ100BUV3B







































































































































































































































































































































































































Отзывы:

Нет отзывов