Daikin BPMK928B42 Скачать руководство пользователя страница 248

Страница: 248 / 410

Si18-201

Troubleshooting - Split Type Indoor Unit

Service Diagnosis

235

1.5.3

Operation Halt Due to Fan Motor (AC Motor) or Related Abnormality

Remote
Controller
Display

Indoor Unit LED
Display

Note:

No LED Display on FTK(X)25/35J Series.

Method of
Malfunction
Detection

The rotation speed detected by the hall IC during fan motor operation is used to determine
abnormal fan motor operation.

Malfunction
Decision
Conditions

When the detected rotation speed is less than 50% of the HH tap under maximum fan motor
rotation demand.

Supposed
Causes

Operation halt due to short circuit inside the fan motor winding.

Operation halt due to breaking of wire inside the fan motor.

Operation halt due to breaking of the fan motor lead wires.

Operation halt due to faulty capacitor of the fan motor.

Detection error due to faulty indoor unit PCB (1).

Detection error due to faulty indoor unit PCB (2).

Troubleshooting

Check No.15

Refer to P.309

Rotate the fan by hand.

Check No. 15
Check hall IC

Operate the fan.

Does it rotate?

Does it rotate smoothly?

Is there an output?

Is it at the rated voltage?

Is there conductivity?

Check the capacitor's
conductivity

Check the fan motor voltage.
(immediately after re-start)

Is it at the rated voltage?

Check the fan motor voltage.

YES

Replace the fan motor or indoor
unit PCB.

Replace the fan motor

∗

2 Measure the voltage between

the red and black lead wires of
the fan motor, and check if the
maximum voltage reaches the
rated voltage.

Replace indoor unit PCB (2).
(PCB (1) for FTK(X)25/35J)

Replace the fan motor.

Replace the indoor unit PCB (2)
(PCB (2) for FTK(X)25/35J)

Replace the capacitor.
(Replace PCB (2).)
(PCB (2) for FTK(X)25/35J)

Replace the fan motor.

(MF003)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Содержание BPMK928B42



























































































































































































































































































































































































































Результаты поиска

Содержание BPMK928B42

Отзывы:

Похожие инструкции для BPMK928B42

Бренды по названию

Популярные бренды

Daikin BPMK928B42, Руководство по обслуживанию

Результаты поиска

Содержание BPMK928B42

Отзывы:

Похожие инструкции для BPMK928B42

Бренды по названию

Популярные бренды