D-Link xStack DGS-3420 Series, Справочное руководство

Страница: 152 / 1117

xStack® DGS-3420 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
147
conform - (Optional) Specify the action when packet is in “green color”.
permit - Permit the packet.
replace_dscp - Changes the DSCP of the packet.
<value 0-63> - Enter the replace DSCP value here. This value must be between 0 and 63.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The
resource may be limited so that a counter cannot be turned on. Counters will be cleared when
the function is disabled.
enable - Specifies that the ACL counter parameter will be enabled.
disable - Specifies that the ACL counter parameter will be disabled.
exceed - Specify the action when packet is in “yellow color”.
permit - (Optional) Permit the packet.
replace_dscp - Changes the DSCP of the packet.
<value 0-63> - Enter the DSCP replace value here. This value must be between 0 and 63.
drop - Drops the packet.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The
resource may be limited so that a counter cannot be turned on. Counters will be cleared when
the function is disabled.
enable - Specifies that the ACL counter parameter will be enabled.
disable - Specifies that the ACL counter parameter will be disabled.
violate - Specify the action when packet is in “red color”.
permit - Permit the packet.
replace_dscp - (Optional) Changes the DSCP of the packet.
<value 0-63> - Enter the DSCP replace value here. This value must be between 0 and 63.
drop - Drops the packet.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The
resource may be limited so that a counter cannot be turned on. Counters will be cleared when
the function is disabled.
enable - Specifies that the ACL counter parameter will be enabled.
disable - Specifies that the ACL counter parameter will be disabled.
sr_tcm - Specify the “single rate three color mode”.
cir - Specifies the single rate three color mode used.
<value 0-1048576> - Enter the single rate three color mode value here. This value must be
between 0 and 1048576.
cbs - Specify the “committed burst size”. The unit is Kbytes.
<value 0-131072> - Enter the committed burst size value here. This value must be between 0
and 131072.
ebs - Specify the “Excess Burst Size”. The unit is Kbytes.
<value 0-131072> - Enter the excess burst size value here. This value must be between 0 and
131072.
color_blind - (Optional) Specify the meter mode to be color-blind. The default is color-blind mode.
color_aware - (Optional) Specify the meter mode to be color-aware. When this code is specified,
user could set the “in-coming packet color” by using command “config color_aware”. The final
color of packet is determined by the initial color of packet and the metering result.
conform - (Optional) Specify the action when packet is in “green color”.
permit - (Optional) Permit the packet.
replace_dscp - Changes the DSCP of the packet.
<value 0-63> - Enter the replace DSCP value here. This value must be between 0 and 63.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The
resource may be limited so that a counter cannot be turned on. Counters will be cleared when
the function is disabled.
enable - Specifies that the ACL counter parameter will be enabled.
disable - Specifies that the ACL counter parameter will be disabled.
exceed - Specify the action when packet is in “yellow color”.
permit - Permit the packet.
replace_dscp - (Optional) Changes the DSCP of the packet.