manualshive.com logo in svg

D-Link DES-3326SR, Руководство пользователя

Поделиться
Скачать
D-Link DES-3326SR Скачать руководство пользователя страница 63

D-Link DES-3326SR Layer 3 Switch

 

To change an existing entry, select the group you want to configure and then click the Edit button:

 

 

Figure 6- 4. Link Aggregation 

−

 Edit 

Click to select the new ports in the group. To remove a port from the group, click the Port Member selection box 
so the check disappears. Up to six ports may be selected for each group. Ports that are not available for link 
aggregation have their selection box shaded. Configure the available parameters for the group and click on the 

Apply

 button to make the changes to the group. See the table below for a description of the parameters used for 

the Link Aggregation group. The Type and Group ID can be changed for an existing group. 

The following fields con be configured for Link Aggregation: 

Parameter  

Description 

Group ID 

Allows the entry of a number used to identify the link aggregation group 

−

 

when adding a new group.  Displays the Group ID of the currently selected 
link aggregation group 

−

 when editing and existing entry. 

Type 

Select the type of link aggregation used for the group. If type is not specified 
the default type is Static.  Aggregated ports may be either 

LACP

 or 

Static

. 

LACP indicates the port group as LACP compliant so they can be connected 
to an LACP compliant device.  
Static trunk groups are not able to adjust dynamically and both devices 
connected to the static trunk group must be manually configured if the 
composition of the group is changed. 

Master Port 

<

1

>

 

The Master port of link aggregation group. 

Unit 

Allows the selection of a particular switch in a switch stack, if you have the 
optional stacking module installed and have properly interconnected the 
switches in the switch stack. 

Port Member 

Allows the specification of the ports that will make up the link aggregation 
group.  

Status 

<

Disabled

>

 

This field can be toggled between 

Enabled

 and 

Disabled

. This is used to turn 

a link aggregation group on or off. This is useful for diagnostics, to quickly 
isolate a bandwidth intensive network device or to have an absolute backup 
link aggregation group that is not under automatic control. 

 

 

 

 

53

Содержание DES-3326SR

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды