D-Link 3010F - DES Switch Скачать руководство пользователя | Manualshive

Страница: 236 / 281

background image

Viewing Statistics

Managing RMON Statistics

Page 235

•

Broadcast Packets Received

— Displays the number of good broadcast packets received on the interface

since the device was last refreshed. This number does not include Multicast packets.

•

Multicast Packets Received

— Displays the number of good Multicast packets received on the interface

since the device was last refreshed.

•

CRC & Align Errors

— Displays the number of CRC and Align errors that have occurred on the interface

since the device was last refreshed.

•

Undersize Packets

— Displays the number of undersized packets (less than 64 octets) received on the

interface since the device was last refreshed.

•

Oversize Packets

— Displays the number of oversized packets (over 1518 octets) received on the interface

since the device was last refreshed.

•

Fragments

— Displays the number of fragments (packets with less than 64 octets, excluding framing bits, but

including FCS octets) received on the interface since the device was last refreshed.

•

Jabbers

— Displays the total number of received packets that were longer than 1518 octets. This number

excludes frame bits, but includes FCS octets that had either a bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a bad FCS with a non-integral octet (Alignment Error) number. The field
range to detect jabbers is between 20 ms and 150 ms.

•

Collisions

— Displays the number of collisions received on the interface since the device was last refreshed.

•

Frames of

xx

Bytes

— Number of

xx

-byte frames received on the interface since the device was last

refreshed.

2.

Select an interface in the

Interface

field. The RMON statistics are displayed.

Resetting RMON Statistics Counters

1.

Open the

RMON Statistics Page

.

2.

Click

. The RMON statistics counters are cleared.

«
...
234
235
236
237
238
...
»

Содержание 3010F - DES Switch


























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3010F - DES Switch

Бренд: FAAC Страницы: 2

Бренд: vantiva Страницы: 58

EtherDevice EDS-4009 Series

Бренд: Moxa Technologies Страницы: 18

Бренд: TP-Link Страницы: 2

Бренд: StarTech.com Страницы: 10

Бренд: PKP Страницы: 11

Бренд: PNI Страницы: 92

Бренд: Key Digital Страницы: 20

Omni-Rupter Series

Бренд: S&C Страницы: 31

IES-5222T Series

Бренд: Lantech Страницы: 30

Liquipoint FTW33

Бренд: Endress+Hauser Страницы: 48

Бренд: SICK Страницы: 299

Бренд: Dahua Страницы: 12

Бренд: FIBERROAD Страницы: 30

Бренд: Generac Power Systems Страницы: 2

OSD2251P Series

Бренд: Optical Systems Design Страницы: 48

DCRS-5200 Series

Бренд: Digital China Networks Страницы: 4

8 Port 10/100 Ethernet Switch

Бренд: OnQ Technologies Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды