D-Link 3010F - DES Switch страница 112 Скачать руководство пользователя

Страница: 112 / 281

Configuring VLANs

Defining VLAN Interface Settings

Page 111

•

Exclude (Gray)

— Excludes the interface from the VLAN. However, the interface can be added to the VLAN

through GARP.

•

Forbidden (Red)

— Denies the interface VLAN membership, even if GARP indicates the port is to be added.

Defining VLAN Interface Settings

The

VLAN Interface Settings Page

contains fields for managing ports that are part of a VLAN. The port default

VLAN ID (PVID) is configured on the

VLAN Interface Settings Page

. All untagged packets arriving at the device

are tagged with the port PVID. To define VLAN interfaces:

Click

Basic Setup > VLAN > Membership > Interface Settings

. The

VLAN Interface Settings Page

opens.

Figure 62: VLAN Interface Settings Page

The

VLAN Interface Settings Page

contains the following fields:

•

Interface

— Displays the port number included in the VLAN.

•

Interface VLAN Mode

— Displays the port mode. The possible values are:

–

General

— Indicates the port belongs to VLANs, and each VLAN is user-defined as tagged or untagged

(full IEEE802.1q mode).

–

Access

— Indicates a port belongs to a single untagged VLAN. When a port is in Access mode, the

packet types which are accepted on the port cannot be designated. Ingress filtering cannot be enabled or
disabled on an access port.

–

Trunk

— Indicates the port belongs to VLANs in which all ports are tagged, except for one port that can

be untagged.

Содержание 3010F - DES Switch


























































































































































































































































































Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды

D-Link 3010F - DES Switch, Руководство пользователя для веб

Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды