D-Link 3010F - DES Switch Скачать руководство пользователя

Страница: 197 / 281

D-Link DES-3010FA/GA User Guide

Page 196

–

Boot Code

— Downloads the Boot file.

•

Download to Master Only —

Downloads the system file only to the Master

•

Download to All Units —

Downloads the system file to all units

Configuration Download

The

Configuration Download

section contains the following fields:

•

Configuration Download

— Indicates that the download is for configuration files. If

Configuration Download

is selected, the Firmware Download fields are grayed out.

•

TFTP Server IP Address

— Specifies the TFTP Server IP Address from which the configuration files are

downloaded.

•

Source File Name

— Specifies the configuration files to be downloaded.

•

Destination File

— Specifies the destination file to which to the configuration file is downloaded. The possi-

ble field values are:

–

Running Configuration

— Downloads commands into the Running Configuration file.

–

Startup Configuration

— Downloads the Startup Configuration file, and overwrites the old Startup

Configuration file.

To Download files:

Open the

File Download Page .

Select the file type.

Define the TFTP server address.

Define the

Source File Name

and

Destination File

fields.

Click

. The files are downloaded.

Содержание 3010F - DES Switch


























































































































































































































































































Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды

D-Link 3010F - DES Switch, Руководство пользователя для веб

Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды