D-Link 3010F - DES Switch Скачать руководство пользователя

Страница: 77 / 281

D-Link DES-3010FA/GA User Guide

Page 76

•

IP Address

—

Lists the RADIUS server IP addresses.

•

Priority

— Displays the RADIUS server priority. The possible values are 1-65535, where 1 is the highest

value. The RADIUS server priority is used to configure the server query order.

•

Authentication Port

— Identifies the authentication port. The authentication port is used to verify the

RADIUS server authentication. The authenticated port default is 1812.

•

Number of Retries

— Defines the number of transmitted requests sent to the RADIUS server before a failure

occurs. The possible field values are 1-10. Three is the default value.

•

Timeout for Reply

— Defines the amount of time (in seconds) the device waits for an answer from the

RADIUS server before retrying the query, or switching to the next server. The possible field values are 1-30.
Three is the default value.

•

Dead Time

— Defines the amount of time (in minutes) that a RADIUS server is bypassed for service

requests. The range is 0-2000. The default is 0 minutes.

•

Source IP Address

— Defines the source IP address that is used for communication with RADIUS servers.

•

Usage Type

— Specifies the RADIUS server authentication type. The default value is

All

. The possible field

values are:

–

Log in —

The RADIUS server is used for authenticating user name and passwords.

–

802.1X

— The RADIUS server is used for 802.1X authentication.

–

All

— The RADIUS server is used for authenticating user names and passwords, and 802.1X port

authentication.

•

Remove

— Removes a RADIUS server. The possible field values are:

–

Checked

— Removes the selected RADIUS server.

–

Unchecked

— Maintains the RADIUS servers.

Click .

The

Add Radius Server Page

opens:

Содержание 3010F - DES Switch


























































































































































































































































































Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды

D-Link 3010F - DES Switch, Руководство пользователя для веб

Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды