D-Link 3010F - DES Switch Скачать руководство пользователя

Страница: 237 / 281

D-Link DES-3010FA/GA User Guide

Page 236

Configuring RMON History

This section contains the following topics:

•

Defining RMON History Control

•

Viewing the RMON History Table

Defining RMON History Control

The

RMON History Control Page

contains information about samples of data taken from ports. For example, the

samples may include interface definitions or polling periods. To view RMON history information:

Click

Advanced Setup > RMON > History > History Control

. The

RMON History Control Page

opens.

Figure 151:RMON History Control Page

The

RMON History Control Page

contains the following fields:

•

History Entry No.

— Displays the entry number for the History Control Table page.

•

Source Interface

— Displays the interface from which the history samples were taken. The possible field

values are:

–

Port

— Specifies the port from which the RMON information was taken.

–

LAG

— Specifies the port from which the RMON information was taken.

•

Sampling Interval

— Indicates in seconds the time that samplings are taken from the ports. The field range

is 1-3600. The default is 1800 seconds (equal to 30 minutes).

•

Samples Requested

— Displays the number of samples to be saved. The field range is 1-65535. The default

value is 50.

Содержание 3010F - DES Switch


























































































































































































































































































Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды

D-Link 3010F - DES Switch, Руководство пользователя для веб

Результаты поиска

Содержание 3010F - DES Switch

Отзывы:

Похожие инструкции для 3010F - DES Switch

Бренды по названию

Популярные бренды