Starting and Configuring the Device
Booting the Device
Page 33
Booting the Device
The assumed bootup information is as follows:
•
The device is delivered with a default configuration.
•
The default user name is admin
•
The default passwordis blank.
To login, perform the following steps:
1.
Press Enter twice in rapid succession. The auto baud-rate process synchronizes the host and the device.
2.
Enter the user name, admin. The default password is blank.
To boot the device, perform the following steps:
1.
Ensure that the device port console is connected to a VT100 terminal device or VT100 terminal emulator.
2.
Locate an AC power receptacle.
3.
Deactivate the AC power receptacle.
4.
Connect the device to the AC receptacle.
5.
Activate the AC power receptacle.
The device goes through Power On Self Test (POST). POST runs every time the device is initialized and checks
hardware components to determine if the device is fully operational before completely booting. If a critical problem
is detected, the program flow stops. If POST passes successfully, a valid executable image is loaded into RAM.
POST messages are displayed on the terminal and indicate test success or failure.
As the device boots, the bootup test first counts the device memory availability and then continues to boot. The
following screen is an example of the displayed POST:
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
FRU Validation Test...............................PASS
BOOT Software Version x.x.x.xx Built 22-Jan-2005 15:09:28
Processor: xxxxxx xxxxx , xxx MByte SDRAM.
I-Cache x KB. D-Cache x KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
The boot process runs for approximately 60 seconds.
The auto-boot message displayed at the end of POST (see the last lines) indicates that no problems were
encountered during boot.
During boot, the Startup menu can be used to run special procedures. To enter the Startup menu, press
<Esc>
or
<Enter>
within the first two seconds after the auto-boot message is displayed.
Содержание 3010F - DES Switch
