Crestron e-control Vote Скачать руководство пользователя

Страница: 98 / 135

Crestron

e-control Vote SW-VOTE

••

Appendices

Installation & Reference Guide — DOC. 5822

Excuse

Voting Console

Description

Seat excuses itself

Direction

control system to Voting Computer

Type

Digital

Value

Pulse

Expected Reply

None

Comments

This signal is accepted by the Voting Computer only while the floor is opened for
voting only. Even when the floor is opened, it will be ignored

when the signal block is not configured to allow excuses [

Excuse (conflict-of-

interest)

checkbox,

Additional vote buttons

frame,

Rules

tab,

Voting Console Signal

Block Definition

window];

when the seat has been excused from the vote, either by the operator prior to

opening the floor, or by the seat itself via a prior pulse of its

Excuse

signal; or

when taking attendance (voting sequence started by

Attendance

signal rather than

Start

signal).

The seat may pulse its

Yes, No,

and

Abstain

signals at will while the floor is

opened. The most recently pulsed signal is considered definitive at the moment the
floor is closed. However, if the seat pulses its

Excuse

signal, further pulses of any

of these signals are be ignored. (The operator can however adjust the seat’s vote
after the floor is closed.)

The definition of the

Abstain

signal set is optional. Note however that even when

not defined, the signal block may still be configured to allow abstentions. In such a
case, while the seat would not be able to abstain, his vote could still count as an
abstention under the following two circumstances:

The default vote is set to Abstain (

ABSTAIN

checkbox,

Default votes

frame,

Rules

tab,

Voting Console Signal Block Definition

window).

After the floor is closed , the Operator adjusts the seat’s vote from the touchpanel

or from the

Vote Proctor

window.

See Also

Yes, No, Start, Attendance

Содержание e-control Vote








































































































































Результаты поиска

Содержание e-control Vote

Отзывы:

Похожие инструкции для e-control Vote

Бренды по названию

Популярные бренды

Crestron e-control Vote, Руководство пользователя

Результаты поиска

Содержание e-control Vote

Отзывы:

Похожие инструкции для e-control Vote

Бренды по названию

Популярные бренды