Crestron e-control Vote Скачать руководство пользователя

Страница: 115 / 135

Crestron

e-control Vote SW-VOTE

115

••

Appendices

Installation & Reference Guide — DOC. 5822

Start

Voting Console

Description

Open floor to voting

Direction

control system to Voting Computer

Type

Digital

Value

Pulse

Expected Reply

Success:

StateStart

assert; followed by

Done

pulse

Failure:

ErrString

Comments

This is one of two signals that can be used to start the voting sequence; the other
is the

Attendance

signal.

In either case, if an agenda item is required and one has not been selected or
entered, the following string is sent through the

ErrString

signal:

Please select or enter an agenda item description.

•

An agenda item is only required however if
the

Auto-name an unnamed vote when

started from Voting Computer

box is

unchecked (See “Voting Console signal
block definition: Enable

Displays the

Vote Proctor

window when the

signal block is enabled. Also enables the

Voting | Start Voting

command. If

unchecked, the window cannot be opened at
all.

•

Auto-name vote

The server generates a name for the vote based
on the current date and time, in the form

yymmdd_hhmmss.

Applies only to an

otherwise unnamed vote; and only when the
vote is started from

Vote Proctor

window. The

Start Vote

button, normally disabled until an

agenda has been set, is enabled. Note that this
option is independent of the option of the
same name under the

Control System Interface

tab

•

Secret Ballot

During a vote, seat icons displayed in the

Vote

Proctor

window turn grey as they vote. Actual

votes are tallied to the

Vote Proctor

window

only after the floor is closed.

OTE

A “secret ballot” is actually only secret

while the floor is opened. Once the floor is
closed, the vote is published.

The

Control System Interface

Tab” page 37.)

Otherwise, either signal is only valid between votes (after

NewVote

pulse and

before assertion of any of the “state” signals). If issued at the wrong time, one of
the following descriptive error messages is sent through the

ErrString

signal:

VOTE IN PROGRESS, FLOOR OPENED:

Press END VOTE or ABORT VOTE.

VOTE IN PROGRESS, FLOOR CLOSED:

Press seats to change votes; DISPLAY; or ABORT.

Содержание e-control Vote








































































































































Результаты поиска

Содержание e-control Vote

Отзывы:

Похожие инструкции для e-control Vote

Бренды по названию

Популярные бренды

Crestron e-control Vote, Руководство пользователя

Результаты поиска

Содержание e-control Vote

Отзывы:

Похожие инструкции для e-control Vote

Бренды по названию

Популярные бренды