Crane BevMax 4, Техническое руководство

Страница: 9 / 103

8
size. If the vender is to be used in a bank of
equipment, check the top and sides for proper
alignment. If you are unable to properly level the
vender, select an alternate location. NEVER PLACE
OBJECTS UNDER THE LEVELING LEGS OF THE
VENDER
DANGER
THE VENDER MUST BE PROPERLY
LOCATED AND LEVELED. IF THE
MACHINE WILL BE SUBJECT TO
USER MISUSE OR VANDALISM IT IS
RECOMMENDED THAT THE
VENDER BE SECURED TO THE
FLOOR OR WALL AS DESCRIBED
IN CRANE MERCHANDISING
SYSTEMS DIXIE-NARCO
TECHNICAL BULLETIN 344 TO
MINIMIZE THE RISK OF INJURY OR
DEATH FROM TIPPING. CALL THE
CRANE MERCHANDISING
SYSTEMS TECHNICAL SERVICE
DEPARTMENT OR YOUR CRANE
MERCHANDISING SYSTEMS
REPRESENTATIVE FOR
ASSISTANCE.
SPACE THE VENDER
Do not block the rear of the vender. Maintain a
minimum of 4 inches (10 cm) from the wall to ensure
adequate airflow to the condenser and compressor.
At the rear of the vender, make sure nothing obstructs
the air exhaust at the bottom of the cabinet.
WARNING
TO AVOID THE POSSIBILITY OF A
FIRE HAZARD, DO NOT STORE
ANYTHING OR ALLOW DEBRIS OF
ANY KIND TO ACCUMULATE IN THE
BOTTOM OF THE DOOR, IN THE
BOTTOM OF THE SERVICE AREA,
IN AND AROUND THE
REFRIGERATION COMPARTMENT
OF THE CABINET, OR IN FRONT OF
THE EVAPORATOR AND
CONDENSER COILS.
INSTALLING PRICE LABELS
Pricing labels included in the literature package kit.
Remove the pricing label sheets from the service
manual package and gently remove the label
corresponding to the vend price of each selection by
tearing at the perforation. The label is installed at the
top of the front knuckle. Once installed, push the label
firmly against the front of the knuckle. This will insure
the label is locked in place.
INSTALLING PRODUCT ID CARDS
To assist with consistent loading, product ID cards
can be installed in the product pusher to designate to
the route driver which product the column is set for.
To install the flavor card, simply detach it from the
sheet at the perforation and slide it into the slots in the
product pusher. Contact your graphics supplier to
purchase as needed.
COIN CHANGERS & OTHER
ACCESSORIES
The vender can have an MDB coin changer installed
and can have an MDB bill acceptor installed as well.
Note: BevMax 4 5800-4/3800-4 will work with an MDB
bill acceptor only. If the MDB coin changer and other
MDB accessories are not factory installed, refer to the
instructions received form the manufacturer of the
MDB coin changer and other MDB accessories for
proper set-up and installation.
The vender will support the following Domestic MDB
coin changers:
All available NRI MDB
All available Coinco MDB
All available Mars MDB
All available Conlux MDB
The vender will support the following domestic MDB
Bill validators:
All available Cashcode MDB
All available Coinco MDB
All available Mars MDB
All available Conlux MDB
The vender will support MDB card readers.
SETTING THE TEMPERATURE
CONTROL
This vender is equipped with an electronic
temperature sensor. Defrost is controlled both
electronically based on run time of the compressor
and with a manual Defrost thermostat. The temp
sensor is factory pre-set to maintain a cabinet
temperature of 37º Fahrenheit (2.7ºC). It is also a
good practice to ensure the proper operating
temperature prior to installing the vender on location.
To set the temperature, apply power to the vender
and allow it to run for several hours with the glass
door closed or until the minimum cabinet temperature
is achieved. Then, using the method below, verify the
temperature inside the cabinet:
With an electronic temperature sensor, use the
keypad on the service door to show cabinet
temperature in Fahrenheit by pressing the F key
followed by the asterisk (
” ) key or in Centigrade by
pressing the C key followed by the asterisk key. The
temperature will be shown on the digital display
located on the front of the service door.