Crane BevMax 4, Техническое руководство

Страница: 20 / 103

19
8625CF and Generic Venders prior to 8600AG.
Extended Cup Enabled is used in all BevMax 4
5800-4 Venders.
•
Key F = Cup Sensor. Press key F and the
display will show “Cup Sensor Off”. Press the
“
”
” key to toggle the Extended Cup to the On
setting. Cup Sensor On is used in all BevMax 4
5800-4 Venders produced 3/26/08 and after.
•
Key 1
= Position Test. Note: The left or top door
switch (depending on the mounting bracket in
use) must be pulled to the out position to
perform this test.
Caution: XY needs to be in
the home position before performing this
test.
If you look at the control board the green,
amber (yellow), and red lights should be on at
this time. If not please check the following:
Green light is for home switch on bottom of port
cup, amber light is for home switch on left side
of Y motor assembly, red light is for home switch
for picker cup plunger. Press the number 1 key
and the display will show a set of numbers (ie
###### # ###### #). To position test press the
following:
a. Shelf letter (A,B,C,D,E) to travel
to selected shelf.
b. Column number (1,2,3,4,5,6,7,8,
& 9) to travel to selected
column.
c. Key “0” to cycle cup plunger to
hit column target.
d. Key “F” to return cup to home
position.
e. Key “ ” “ is all stop.
•
Key 2
= Port Test. Press the number 2 key and
the display will show four numbers “####”. The
1
st
# is Port Open switch and 0 = Port not open
or 1 = Port opened. The 2
nd #
is Port Closed
switch and 0 = Port not closed or 1 Port closed.
The 3
rd
# is Sensor and 1 = Sensor on or 0 =
Sensor off. The 4
th
# is Vend detect (only if
Sensor is on) 0 = No product in port or 1 Product
in port. To test the port press the following:
f. Key “A” to open port.
g. Key “B” to close port.
h. Key “C” to turn sensor on.
When turned on and something
is placed in the port a red LED
will light on the board.
i. Key “D” to turn sensor off.
j. Key “E” to toggle Cup LED light.
k. Key “F” to toggle Port LED light.
l. Key “*” All Stop on any of these
tests.
•
Key 3
=
Delivery Cup Check. Press the number
3 key and the display will show “On:0 In:0
Out:0 Hm:1”. Note: The door switch (or left
door switch on e-lock venders) must be pulled to
the out position to perform this test.
Caution:
XY needs to be in the home position before
performing this test. Press the “
”
” key and
the display will show “Port Sensor On/Off On:0
In:0 Out:0 Hm:1”. Press the “
”
” key to toggle
the Port Sensor to the Off setting. To test the
Port with the Port Sensor On, press the “
”
” key
and Display will show “Port Sensor On - On:1
In:0 Out:0 Hm:1”. To perform tests press the
following:
a. Shelf letter (A,B,C,D,E) to travel to
selected shelf.
b. Column number (1,2,3,4,5,6,7,8, &
9) to travel to selected column.
c. Key “0” to cycle cup plunger to hit
column target. The Out:0 will
change to 1 momentarily and back
to 0 and the Hm:1 will change to 0
momentarily and back to 1.
d. Key “F” to return cup to home
position.
e. If the delivery cup has a cup sensor
in it, place a package in the delivery
cup and the In:0 will change to In:1,
remove package and it will change
to In:0.
There are 4 pieces of data shown on the
display labeled as “On”, “In”, “Out”,
and “Hm”.
“On” indicates whether the delivery cup
sensor if present is turned on or off. A
“1” indicates it is on and a “0” indicates
it is off.
“In” indicates whether the delivery cup
sensor detects product in the cup. In
order to be detected the product must be
placed in the cup after the sensor was
turned on. If a product is in the cup
when the sensor is turned on, the sensor
will not detect it. A “1” indicates
product is detected and a “0” indicates it
is not. When the sensor is turned off,
there will be a “0” regardless of whether
product is in the cup or not. The Yellow
LED on the controller also will be on
when a “1” is displayed.
“Out” indicates whether the picker out
switch is closed. A “1” indicates that
the picker out switch is closed and a “0”
indicates it is opened (plunger at home
position). Please note that the switch is
moved by the cam, not the picker.
Pulling the picker out by hand will not