background image

− 3 −

Introduction

 Safe Operation

In order to use the Gas Detector safely, be sure to observe the following items.

*Special Instruction and Warning :

Use Panasonic LR6XJK, Toshiba LR6, or Duracell MN1500 batteries.  Use of any other 

manufacuturer or type will violate intrinsic safety requirement.  Remove and replace the batteries 

only in areas known to be non-hazardous.  

1. Introduction (continued from previous page)

DANGER

  If the gas alarm turns ON, immediately take all necessary measures to 

prevent explosion accidents.

WARNING

  Be sure to turn ON the Gas Detector in clean air. Zero calibration is 

done automatically. Therefore, the wrong gas concentration will be 

displayed if zero calibration is done in a gas atmosphere.

  Do not close the suction port or exhaust port, or no gas detection will be 

possible.

  Use the filter element in a clean state. Normal detection cannot be 

performed if the filter element is dirty or moisture adheres to the filter 

element.

CAUTION

  Remove the batteries and store the Gas Detector if it is not to be used for a 

long time.

  The Gas Detector has an explosion-proof construction.  Do not disassemble 

or modify the Gas Detector or change the structure or electric circuits of 

the Gas Detector.  Otherwise, the explosion-proof performance of the Gas 

Detector will be damaged.

  Do not leave the Gas Detector in high-temperature or highly humid places, 

or the performance of the Gas Detector may be adversely affected.

  Keep the Gas Detector away from radical temperature or humidity changes, 

walkie-talkie, mobile phone, or its performance may be adversely affected.

  Keep the Gas Detector away from great atmospheric pressure changes, 

or the performance of the sensor may be adversely affected or the sensor 

may be damaged.

  Do not drop, hit, or apply a strong mechanical shock to the Gas Detector, or 

its performance may be adversely affected.

  The Gas Detector is not drip-proof but the leather case protects the Gas 

Detector from water drips. Keep the Gas Detector away from water drips 

as much as possible.

  Keep the Gas Detector away from places close to where silicone sealing 

materials are being used or silicon gas atmospheres, or its performance 

may be damaged.

  Do not let the Gas Detector draw in water.

  Do not use any batteries other than the specified one. otherwise it would 

damage the explosion-proof performance.

Содержание XP-3110

































Отзывы: