background image

   

 

STW5-SE Microphone Speaker Kit Instructions

 

 

 
The STWI5-SE is a two-way audio surveillance system (intercom accessory) designed to be used with DVRs, I/P cameras 
etc. Note- the audio signals going into and out of the STW1-SE are “line level” (0dbm). STW1-SEs are suitable for outdoor 
use but, exposure to driving rain should be avoided. 
 
 

STW1-SE Microphone / Speaker Placement. 

Locate the STW1-SE as close as possible to the area of interest in the space to be monitored. If a large area is to be 
monitored, locate the STW1-SE in the middle of the space if possible. Do not mount the STW1-SE near air conditioning 
vents, light fixtures or electrical equipment. The STW1-SE should be placed at least 5 feet away from the subject(s) to be 
monitored. The STW1-SE is still useable in the range of 15-25 feet but is dependent on the level of background noise in 
the area. Experimentation in the environment will determine what distances work best.  
 

STWI-1 Interface box location

 

The STWI-1 interface box is designed to be located next to a DVR or I/P camera. The STWI-1 requires a 120VAC power 
source within 3 feet of its location. If this is not possible in your application, you can splice in up to 100 feet of 20 awg, 2 
conductor cable to extend the distance between the AC power source and the STWI-1.  
 

Cable Runs 

Run 2 each 22 gauge, stranded, two conductor shielded cable between each STW1-SE microphone / speaker and the 
STWI-1 interface. Keep both cable run distances under 250 feet and away from AC power sources, light fixtures and 
electrical equipment. 

See Figure 1 for connection diagram. 

 
Mounting 

The STW1-SE is designed to surface mount on any flat hard surface. A 5 foot height is recommended. Cables can be 
routed into the STW1-SE via the ½” “knock out” on the rear of the enclosure. 
 

STW1-SE Optional Call Switch 

Connect this switch to equipment that permits a “page” signal input. It is a N.O. (normally open) dry switch contact. Use a 
22awg 2 conductor for this cable run. 
 

Adjusting the STW1-SE Microphone Gain and Speaker Volume 

Start with a midrange setting of the gain control on the STW1-SE. Adjust the VR1 c or – for maximum microphone 
clarity. If the sound at the DVR is distorted, rotate the control towards the – mark (counter- clockwise). If the volume at the 
amplifier is too low, rotate the control towards the + mark (clockwise). Adjust the “talk-back” speaker volume to the 
appropriate level using the blue level control located near the “70v / line” switch. 
 

Setting the STW1-SE Microphone Jumpers 

The SM1 microphone has jumper selectable treble boost and limiter circuits. The treble boost circuit when jumpered in, 
emphasizes the high frequency sounds that the microphone picks up. This is useful for improving the sound quality on 
slow speed tape recordings (VCR time-lapse recordings). The limiter circuit, when jumpered in, automatically keeps the 
SM1’s output at a relatively constant level. This eliminates the need for the listener to reduce the volume control on the 
amplifier when sounds get louder.  

Note:

 Do not use the STW1-SE’s limiter circuit if you are using a tape recorder or other device that uses an AGC or limiter 

circuit. Most tape recorders have limiter circuits. The recommended jumper settings are as follows: 
 
 

Stand-alone Application 

 

Tape Recorder Application 

Limiter “IN” 

“OUT” 

Treble Boost 

“OUT” 

“IN” 

 

 

 

 

Отзывы: