CORVUS 70E V2 Скачать руководство пользователя страница 9

Страница: 9 / 29

ARF® MODEL

Items Required to Complete This Model

•

1000-1200 Watt, 300g class electric motor

•

70-100A ESC

•

4 or 5 mini size high torque servos (Hitec HS5245 or HS 7245)

*1 or 2 servos for elevators

•

Appropriate servo arms

•

Servo wire extensions. two 6”, two 12”

•

Appropriate Lipo batteries (6S 2600-3300mah)

•

Receiver of your choice (minimum 4 channels)

•

radio

your

choice

Shop Supplies/Tools

•

Covering Iron and heat gun

•

Hobby tools such as screwdrivers, hobby knife, drill and drill bits, piers, etc.

•

Thick and Thin CA adhesives

•

30 minute Epoxy

•

Isopropyl alcohol

•

Ruler or tape measure

•

Blue thread-lock or equivalent

•

Adhesive backed Velcro and Velcro strap for battery retention

Note: please read all the instructions before you begin construction. Handle the parts of this kit with

care so you do not damage any of the structure or covering. Inspect all the parts for any shipping

damage and report any issues to as soon as you can. Make sure you have a flat and sturdy workbench

and follow all safety advice for the tools and adhesives you plan to use

Aircraft Covering

Varying temperatures and storage delays can cause covering material to loosen over time and

transportation.

We recommend lightly going over all the covering with a covering iron set at

medium temperatures

. Be sure to use a soft cover over your iron so you do not scratch the covering

surface. Be sure you go over all seams and edges of the covering to assure it is secure to the airframe

Содержание 70E V2






























Результаты поиска

Содержание 70E V2

Отзывы:

Похожие инструкции для 70E V2

Бренды по названию

Популярные бренды

CORVUS 70E V2, Инструкция по эксплуатации

Результаты поиска

Содержание 70E V2

Отзывы:

Похожие инструкции для 70E V2

Бренды по названию

Популярные бренды