manualshive.com logo in svg

Conviron ADAPTIS A1000, Инструкция по установке, эксплуатации и обслуживанию

Conviron ADAPTIS A1000 - инновационный климатический камера для исследований. Скачайте бесплатно Руководство по установке, эксплуатации и техническому обслуживанию на manualshive.com. Этот удобный manual поможет вам максимально эффективно использовать все возможности этого продукта.

Поделиться
Скачать
background image

 
 
 
 

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL 

 

 

February 2016 | 256574-ENG

 

R01     2-25 

 

Multiple Lamp Fixtures per Shelf 

Install the lamp fixture with the cable closest to the back wall of the chamber. 

 

To install multiple lamp fixtures per 
shelf: 

1.  Install the lamp fixture supports and 

install the fixtures onto the shelves, 
following the instructions on page 2-
24. 

2.  Ensure that the fixture with the plug is 

at the back of the chamber and plug 
the front fixture into the back fixture 
(Figure 2-30). 

3.  Remove the cap from the receptacle 

and connect the back fixture plug into 
the receptacle on the wall. 

4.  Repeat with all the remaining fixtures. 
 

 

 

The chamber is now ready to operate. 
Read the startup instructions carefully 
before proceeding with the start up. 

   

 

 

Figure 2-30 

IN Multiple Lamp Fixture Installation Detail 

 
 

 

Figure 2-31 

IN Kit Installed 

 

The fixtures without a cable must always be installed closer to the door to enable 
correct daisy chain connections. 

The maximum operating levels of light for this kit must be set at the controller. To edit 
the factory default setting, refer to the included Operator’s Manual. 

Содержание ADAPTIS A1000

































































Отзывы:

Нет отзывов

Похожие инструкции для ADAPTIS A1000

Бренды по названию

Популярные бренды

Загрузить еще бренды