manualshive.com logo in svg

Conviron ADAPTIS A1000, Инструкция по установке, эксплуатации и обслуживанию

Conviron ADAPTIS A1000 - инновационный климатический камера для исследований. Скачайте бесплатно Руководство по установке, эксплуатации и техническому обслуживанию на manualshive.com. Этот удобный manual поможет вам максимально эффективно использовать все возможности этого продукта.

Поделиться
Скачать
background image

 
 
 
 

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL 

 

 

February 2016 | 256574-ENG

 

R01     2-1 

 

2 KIT 

INSTALLATION 

If the chamber has a kit installed, locate the installation instructions in this manual for that kit and 
reverse the steps to remove the existing kit before proceeding with a new installation. 

2.1 Preparation 

Read and understand these instructions before proceeding with unpacking and installing the new 
A1000 chamber. 

The A1000 chambers are generally shipped in two crates – one for the chamber and another for 
the kit. To avoid damage, keep the chamber crated until it is ready for placement within the facility. 

Before moving the chamber to its final location, ensure there is enough clearance through 
doorways, hallways, and elevators, and along the route to the installation site. You may need to 
uncrate it before moving it. The door may be removed from the chamber if absolutely necessary. 
Contact Conviron for door removal instructions. 

 

 

Figure 2-1 

Empty A1000 Chamber 

Содержание ADAPTIS A1000

































































Отзывы:

Нет отзывов

Похожие инструкции для ADAPTIS A1000

Бренды по названию

Популярные бренды

Загрузить еще бренды