manualshive.com logo in svg

Conviron ADAPTIS A1000, Инструкция по установке, эксплуатации и обслуживанию

Conviron ADAPTIS A1000 - инновационный климатический камера для исследований. Скачайте бесплатно Руководство по установке, эксплуатации и техническому обслуживанию на manualshive.com. Этот удобный manual поможет вам максимально эффективно использовать все возможности этого продукта.

Поделиться
Скачать
background image

 
 
 
 

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL 

 

 

February 2016 | 256574-ENG

 

R01     1-1 

 

1 PRECAUTIONS 

The equipment is intended to be installed, operated, maintained, and serviced only by trained 
personnel, according to the instructions and precautions described in the manuals provided by 
Conviron. 

The following precautions are intended to help guide users in the safe operation of Conviron 
chambers. 

1.1  Hazard Identification Symbols 

The following symbols are used throughout this manual and/or on the equipment to draw your 
attention to important warnings, guidelines and product information. 

Table 1-1 

Hazard Identification Symbols 

Symbol Description 

 

The “

HAZARD WARNING

” symbol is used whenever a hazard exists which 

could cause personal injury or potential equipment damage, and requires 
correct procedures/practices for prevention. 

 

The “

IMPORTANT INFORMATION

” symbol is used to identify operating 

procedures which must be followed to ensure smooth and efficient equipment 
operation. 

 

The “

ELECTROSTATIC DISCHARGE

” symbol is used to identify equipment 

which is sensitive to electrostatic discharge. 

 

The “

BURN HAZARD/HOT SURFACE

” symbol is used to identify surfaces 

which are hot enough to cause personal injury. 

 

The “

PROTECTIVE EARTH-GROUND-MANDATORY ACTION

” symbol is 

used to identify the protective earth connection. 

 

The “

PROTECTIVE EARTH-GROUND

” symbol is used to identify the 

protective earth connection. 

Содержание ADAPTIS A1000

































































Отзывы:

Нет отзывов

Похожие инструкции для ADAPTIS A1000

Бренды по названию

Популярные бренды

Загрузить еще бренды