manualshive.com logo in svg

Control Techniques Epsilon EP-P, Справочное руководство

Управление техникой Epsilon EP-P - это мощный преобразователь частоты для промышленных приложений. Вы можете загрузить бесплатное руководство по эксплуатации и справочное руководство с нашего веб-сайта. Получите детальную информацию о настройке и использовании этого продукта. Загрузите их с manualshive.com.

Поделиться
Скачать
background image

Epsilon EP-P Drive Reference Manual

43

Revision A4

www.controltechniques.com

hit, then the axis can be jogged in the + direction.

Software Travel Limit + (SoftwareTravelLimitPlusPosn)

If the absolute position is greater than or equal to this value the SoftwareTravelLimitPlusActive source shall activate. 
A rising edge occurs when the absolute position is greater than or equal to the parameter SoftwareTravelLimitPlusPosn. A 
falling edge will be generated as soon as the above is not true.

Software Travel Limit - (SoftwareTravelLimitMinusPosn)

If the absolute position is less than or equal to this value the SoftwareTravelLimitMinusActivate shall activate. 
A rising edge occurs when the absolute position is less than or equal to the parameter SoftwareTravelLimitMinusPosn. A 
falling edge will be generated as soon as the above is not true.

3.9.3

Rotary Group

Rotary Rollover Check Box

Select this check box (RotaryRolloverEnable) to enable (or disable if clear) the rotary rollover feature.

Rotary Rollover

This parameter (RotaryRolloverPosn) is used in rotary applications and determines the position at which the internal position 
counter will be reset to zero. 

Example:

The user has a rotary table application with distance user units of degrees, 360.00 degrees/1 rev. The Rotary Rollover 
would be set to a value of 360°.
The motor is travelling in the positive direction. As the feedback position reaches 359.999 and continues on, the feedback 
position will reset (or roll-over) to zero. If the motor changes direction and travels in the negative direction, the position will 
rollover at 0 to 359.999 degrees and count down. The resolution of the rotary rollover point is determined by the Distance 
Units Decimal Places parameter on the User Units view in the PowerTools Pro software.

If an absolute index is used with a non-zero rotary rollover point, the Epsilon EP-P drive will calculate the shortest path to its 
destination and move in the required direction. 
To force the motor to run a certain direction, use the Rotary Plus or Rotary Minus type of indexes.

3.9.4

Online Tab (not shown)

While online, the following real-time data will be displayed. 

Motor Position Group

Position Command

This is the commanded position in user units. 

Position Feedback

This is the feedback position of the motor in user units.

Following Error

The Following Error is the difference (in user units) between the Position Command and the Position Feedback. It is positive 
when the Position Command is greater than the Position Feedback.

Encoder Position

The motor position in encoder counts since power up when the value was set to zero. This is a signed 32-bit value. 

3.10

Velocity View

The Velocity View allows the setup of feedrate override details.
By selecting Velocity in the Hierarchy Tree, the Velocity View will appear on the right (see Figure 45). 

Содержание Epsilon EP-P

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Epsilon EP-P

Calpeda EASYMAT 5MM Original Operating Instructions preview
EASYMAT 5MM
Бренд: Calpeda Страницы: 22
Raymarine IO Drive Installation Manual preview
IO Drive
Бренд: Raymarine Страницы: 23
BOCKWOLDT HELICAL GEAR BOXES BC Series Operating Instructions Manual preview
HELICAL GEAR BOXES BC Series
Бренд: BOCKWOLDT Страницы: 70
Eaton DA- -A20 Series Instruction Leaflet preview
DA- -A20 Series
Бренд: Eaton Страницы: 16
Geckodrive GR214V Manual preview
GR214V
Бренд: Geckodrive Страницы: 12
GFA 10003999 10012 Installation Instructions Manual preview
10003999 10012
Бренд: GFA Страницы: 21
GFA 10002226 10011 Installation Instructions Manual preview
10002226 10011
Бренд: GFA Страницы: 20
GFA 10002617 00001 Installation Instructions Manual preview
10002617 00001
Бренд: GFA Страницы: 32
AutomationDirect Leadshine DM322E Quick Start Manual preview
Leadshine DM322E
Бренд: AutomationDirect Страницы: 17
Becker R12/17RO+ Assembly And Operating Instructions Manual preview
R12/17RO+
Бренд: Becker Страницы: 20
Shugart SA1000 Service Manual preview
SA1000
Бренд: Shugart Страницы: 44
Rexnord Falk A Owner'S Manual preview
Falk A
Бренд: Rexnord Страницы: 44
Binks PT-418-CE Instructions Manual preview
PT-418-CE
Бренд: Binks Страницы: 12
ZIEHL-ABEGG FXDM25 Operating Instructions Manual preview
FXDM25
Бренд: ZIEHL-ABEGG Страницы: 123
Eaton PowerXL DH1 Quick Start Manual preview
PowerXL DH1
Бренд: Eaton Страницы: 45
ABB ACS880-01+C135 Series Supplement Manual preview
ACS880-01+C135 Series
Бренд: ABB Страницы: 100
Eaton CROUSE-HINDS ACE10 1 Installation & Maintenance Information preview
CROUSE-HINDS ACE10 1
Бренд: Eaton Страницы: 12
Eaton MVX001A0-1 Quick Start Manual preview
MVX001A0-1
Бренд: Eaton Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды