manualshive.com logo in svg

Control Techniques Epsilon EP-P, Справочное руководство

Управление техникой Epsilon EP-P - это мощный преобразователь частоты для промышленных приложений. Вы можете загрузить бесплатное руководство по эксплуатации и справочное руководство с нашего веб-сайта. Получите детальную информацию о настройке и использовании этого продукта. Загрузите их с manualshive.com.

Поделиться
Скачать
background image

Epsilon EP-P Drive Reference Manual

165

Revision A4

www.controltechniques.com

Enable Limit Distance

Home.#.LimitDistEnable

This parameter enables the specified Home.#.LimitDist.  If not enabled, the home will run indefinitely until the home reference 
is found.

Limit Distance Hit

Home.#.LimitDistHit

This source is activated when the home sensor is not found before the Home Limit Distance is traveled. 

Name

Home.#.Name

The user can specify a name up to 12 alphanumeric characters that allows a descriptive name for the home.

Home Offset Type

Home.#.OffsetType

Selects calculated or specified home offset. Calculated offset is the distance traveled during the deceleration ramp from the 
home velocity. The specified offset allows the user to choose an exact offset from the Home Reference.

If On Sensor 

Home.#.OnSensorAction

If the home sensor input is active when the home is initiated, this parameter determines the direction of motion. Two selections 
are possible.  If "Back off before homing" is selected, the motor will turn in the opposite direction of the home until the home 
sensor is clear and then begin the home.  If "Go forward to next sensor" is selected, the motor will turn in the commanded 
direction until the next rising edge of the sensor is seen.  If using Modbus to view or modify this parameter, 1= Back off before 
homing, 0 = Go forward to next sensor.

Home Reference

Home.#.Reference

This parameter determines how the reference position is determined. The parameter can have one of three different values: 
'Sensor', 'Marker', 'Sensor then Marker'. When the home reference is 'Sensor' the rising edge of the 'Home Sensor' input 
function is used to establish the reference position. When the home reference is 'Marker' the rising edge of the motor 
encoder's marker channel is used to establish the reference position. When the home reference is 'Sensor then Marker' the 
reference position is established using the first marker rising edge after the Home Sensor input function goes active. 

Sensor Trigger

Home.#.SensorTrigger

This destination is usually a sensor input used as a reference for the home. This event is only used if the home is defined by 
sensor or by sensor then marker.

Specified Offset

Home.#.SpecifiedOffset

The specified offset parameter allows the user to specify an exact offset relative to the Home Reference. The commanded 
motion will stop at exactly the offset distance away from the sensor or the marker as specified.

Time Base

Home.#.TimeBase

The time base selects either realtime, which allows velocities, acceleration and deceleration to be based on real time, or 
synchronized, which allows for an external synchronization signal.

Velocity

Home.#.Vel

This parameter sets the target velocity for all of moves in the home. The sign determines the home direction. Positive numbers 
cause motion in the positive direction and negative numbers cause motion in the negative direction in search of the home 
sensor.

Содержание Epsilon EP-P

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Epsilon EP-P

Vacon 20 SERIES Quick Manual preview
20 SERIES
Бренд: Vacon Страницы: 60
Vacon 100 INDUSTRIAL Application Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 192
CnMemory DVD/RW Drive User Manual preview
DVD/RW Drive
Бренд: CnMemory Страницы: 4
Jung TVA 230 NC WW Fitting Instructions preview
TVA 230 NC WW
Бренд: Jung Страницы: 4
Carotron P22194-1 Instruction Manual preview
P22194-1
Бренд: Carotron Страницы: 28
ABB Terra HP Generation 3 CE Instruction Manual preview
Terra HP Generation 3 CE
Бренд: ABB Страницы: 96
Mesa 8I20 Manual preview
8I20
Бренд: Mesa Страницы: 41
Bosch Rexroth IndraDrive Mi Project Planning Manual preview
Rexroth IndraDrive Mi
Бренд: Bosch Страницы: 340
Kieback&Peter DS230 Manual preview
DS230
Бренд: Kieback&Peter Страницы: 10
Omron Varispeed E7 Datasheet preview
Varispeed E7
Бренд: Omron Страницы: 20
PoLabs PoStep25-256 User Manual preview
PoStep25-256
Бренд: PoLabs Страницы: 8
WEG CFW-11 Series Programming Manual preview
CFW-11 Series
Бренд: WEG Страницы: 307
LinMot C1250-LU-XC Manual preview
C1250-LU-XC
Бренд: LinMot Страницы: 20
LinMot C1150-DS-XC-0S Installation Manual preview
C1150-DS-XC-0S
Бренд: LinMot Страницы: 29
HSB Beta 100-D-ZSA Original Assembly And Maintenance Manual preview
Beta 100-D-ZSA
Бренд: HSB Страницы: 38
Maco HAUTAU SKA 50-500 Original Instructions Manual preview
HAUTAU SKA 50-500
Бренд: Maco Страницы: 12
ABB ACS480 Troubleshooting Manual preview
ACS480
Бренд: ABB Страницы: 24
GFA 10003372 00001 Installation Instructions Manual preview
10003372 00001
Бренд: GFA Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды