manualshive.com logo in svg

Control Techniques Epsilon EP-P, Справочное руководство

Управление техникой Epsilon EP-P - это мощный преобразователь частоты для промышленных приложений. Вы можете загрузить бесплатное руководство по эксплуатации и справочное руководство с нашего веб-сайта. Получите детальную информацию о настройке и использовании этого продукта. Загрузите их с manualshive.com.

Поделиться
Скачать
background image

Epsilon EP-P Drive Reference Manual

149

Revision A4

www.controltechniques.com

Cam Table In Motion

Cam.#.CamTableInMotion

This parameter is active (on) when the specified cam table is executing. Note this source may be on even when no physical 
motor motion is occurring. For example the master may not be moving, but the follower is still considered to be in a 
Commanding Motion state.

Cam Table Size

Cam.#.CamTableSize

This parameter is the number of elements entered in the specified cam table.

Writable Check Box

Cam.#.CamTableWritable

Moves the cam table into ram memory so the user can change the cam table values using a program.

Cam Type

Cam.#.CamType

Cam types to choose from are; Master Follower, Absolute MFI, Incremental MFI, Cubic Spline, or Time Based Index. Most 
data entries are “Absolute” which means each point is an absolute distance from the start of the cam table which is an implied 
zero, although the starting value does not have to be zero. The Incremental MFI (Master/Follower/Interpolation) has the 
entries as distance deltas from point to point which means the point is relative to the previous point.

Decel

Cam.#.Decel

This parameter is the maximum deceleration for the Timed Index. The timed index will not decelerate faster than this value.

Distance

Cam.#.Dist

This parameter is the incremental distance the timed index will move.

Final Velocity

Cam.#.FinalVelocity

The cam table profile will exit at this velocity. See Initial Velocity for more information. When using a single cam table, with no 
chaining, simply set the Initial Velocity to zero.

Forward Chain

Cam.#.ForwardChain

This parameter holds the next cam table to initiate when this cam table is completed. If no cam table is to be initiated, this 
parameter should be set to -1 (negative one) to stop the cam at the end of the current table. The cam will then conclude 
execution.
Forward chain and Backward chain can be dynamically changed by a user program. For example, a program monitors the 
cam motion flow and alters the forward and backward chain variables to switch the flow. You can have a start up sequence of 
tables, a running sequence of tables, a shut down sequence of tables and a alternate operation sequence of tables. The 
monitoring program adjusts the chains to dynamically change the cam sequence.
The cam tables themselves can be altered on the fly as long as you are altering the non-executing cam table. Each cam point 
is accessible by the user program provided the Writable check box has been selected.

Index Time

Cam.#.IndexTime

The Timed Base Index will slow down the index velocity so the index will run for this parameter value. The acceleration and 
deceleration will be reduced to meet the distance and index time of this timed base index.

Initial Velocity

Cam.#.InitialVelocity

This is the entry point velocity for the cam table. For Master Follower this is a calculated value. The user should take care in 
matching the velocity transitions when chaining one cam profile into another.
For MFI and Spline cam tables: If the first segment interpolation type is Linear, the initial velocity is the calculated velocity of 
the first segment. When using a single cam table, with no chaining, simply set the Initial Velocity to zero.

Содержание Epsilon EP-P

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Epsilon EP-P

Danfoss VLT AQUA Drive FC 202 Programming Manual preview
VLT AQUA Drive FC 202
Бренд: Danfoss Страницы: 294
Parker Gemini GT6K Quick Reference Manual preview
Gemini GT6K
Бренд: Parker Страницы: 2
Parker 631 Series Manual preview
631 Series
Бренд: Parker Страницы: 59
Masterflex I/P 7593-00 Operating Manual preview
I/P 7593-00
Бренд: Masterflex Страницы: 12
G-U ELTRAL OA Installation And Operating Instructions Manual preview
ELTRAL OA
Бренд: G-U Страницы: 28
GIESSE 01618 Manual preview
01618
Бренд: GIESSE Страницы: 16
Becker VariAir VAU 11/22.3 Operating Instructions Manual preview
VariAir VAU 11/22.3
Бренд: Becker Страницы: 68
Grundfos Redi-Flo Series Installation And Operating Instructions Manual preview
Redi-Flo Series
Бренд: Grundfos Страницы: 16
Simu T5 AUTO SHORT Hz Original Instructions Manual preview
T5 AUTO SHORT Hz
Бренд: Simu Страницы: 32
Baader SteelDrive Focuser User Manual preview
SteelDrive Focuser
Бренд: Baader Страницы: 26
Stanley SCH20 User Manual preview
SCH20
Бренд: Stanley Страницы: 52
HSB Beta 110-ZSE Original Assembly And Maintenance Instructions preview
Beta 110-ZSE
Бренд: HSB Страницы: 28
Sanyo Denki Q1AA04003D Instruction Manual preview
Q1AA04003D
Бренд: Sanyo Denki Страницы: 266
Fagor MCS Innova Series Manual preview
MCS Innova Series
Бренд: Fagor Страницы: 88
Danfoss ADAP-KOOL Drive Programming Manual preview
ADAP-KOOL Drive
Бренд: Danfoss Страницы: 262
Danfoss VLT 5000 Series Instruction preview
VLT 5000 Series
Бренд: Danfoss Страницы: 4
Magnetek Elevator Axial Flux HPV900 2 Series Start Manual preview
Axial Flux HPV900 2 Series
Бренд: Magnetek Elevator Страницы: 13
YASKAWA SGM series Safety Precautions preview
SGM series
Бренд: YASKAWA Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды