Contec CONPROSYS M2M Series Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 103

Contec CONPROSYS M2M Series Скачать руководство пользователя страница 67

—

PLC Communication Settings

—

M2M Gateway PLC Communication Settings

—

67

—

9.

Modbus/RTU Connection

The following is a setting example for communication with Modbus/RTC support device.
This example describes how to install the Modbus simulator software on the viewing terminal for
checking the connection.
See below for the configuration example regarding communication conditions.



Device Connection Example

A connection example between the viewing terminal and the M2MGateway is illustrated below.
In this example, the USB/RS-485 converter is used to connect the viewing terminal and
the M2MGateway.
As for COM port number on Windows, check it in the "Control Panel" - "Device Manager".

- M2M Gateway

-Viewing and simulator terminal

IP address : 1

０

.1.1.200

Subnet mask : 255.0.0.0

IP address : 10.1.1.101
Subnet mask : 255.0.0.0

Device type : HoldingResister
Access range : 03E9h - 03F2h
Access cycle : 1 sec

Device type : Coil
Access range : 03E9h - 03F2h
Access cycle : 500 ms.

Modbus/RTU

*RS-485

Ethernet

*for viewing and settings

Modbus

Simulator

Modbus

Simulator

■

RS-485/USB converter

As for COM port number on

Windows, check it in the Device

Manager.

RS-485 lines

■DIP switch setting

Full duplex Terminator ON

«
...
65
66
67
68
69
...
»

Содержание CONPROSYS M2M Series








































































































Отзывы:

Нет отзывов