Contec CONPROSYS M2M Series Скачать руководство пользователя страница 5

Страница: 5 / 103

—

Introduction

—

M2M Gateway PLC Communication Settings

—

Related Manuals

The manuals related to the product are listed below.
Read them as necessary along with this document.



Must Read the Following Manuals

Name

When to read

Contents

How to get

Product Guide

Must read this after

opening the package.

This lists the product

configuration and describes

the precautions.

Included in the package

(Printed matter)

Setup Manual

Read this when setting

up the product.

This describes the required

items for setup and

configuration procedure.

Download from

the Contec

website (PDF)

Reference Manual

(Hardware)

Read this when

operating the product.

This describes the hardware

aspects such as functions

and settings.

Download from

the Contec

website (PDF)

Reference Manual

(Software)

Read this when setting

up the "CONPROSYS

WEB Setting"

This describes how to set

each function of

"CONPROSYS WEB Setting".

Download from

the Contec

website (PDF)



Read the Following Manuals as necessary.

Name

When to read

Contents

How to get

CONPROSYS Cloud Data

Service 2(CDS2) Manual

Read this to understand

the outline of the

CONPROSYS Cloud

Data Service 2.

This describes the outline

and specification of the

CONPROSYS Cloud Data

Service 2 as well as how to

operate the product

Download from

the Contec

website (PDF)

CONPROSYS Cloud Data

Service 2 Concise Manual

Read this when using

the CONPROSYS Cloud

Data Service 2.

This describes the procedure

to start monitoring

measured data in Cloud Data

Service 2.

Download from

the Contec

website (PDF)

SIM Card Concise Manual Read this when using

the product with SIM

card for communication.

This describes the procedure

to start data transferring

from the M2M controller to

Cloud server.

Download from

the Contec

website (PDF)



Download Manuals

Download the manuals accordingly from the following URL.

Download

https://www.contec.com/download/

Содержание CONPROSYS M2M Series








































































































Результаты поиска

Содержание CONPROSYS M2M Series

Отзывы:

Contec CONPROSYS M2M Series, Руководство пользователя по настройкам связи, Страница: 5 / 103

Результаты поиска

Содержание CONPROSYS M2M Series

Отзывы: