Contec CONPROSYS M2M Series Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 103

Contec CONPROSYS M2M Series Скачать руководство пользователя страница 52

—

PLC Communication Settings

—

M2M Gateway PLC Communication Settings

—

52

—

6.

Ethernet Connection with KEYENCE PLC

The following is a setting example for Ethernet communication with the KEYENCE PLC KV-5000.
For communication with the KV-5000, the PLC communication protocol by Mitsubishi Electric (MC
protocol) is used.
* KEYENCE original communication protocol is not supported as of August 2018.

See below for the configuration example regarding communication conditions.

In this communication example, M2M Gateway setting is configured on the Mitsubishi device with
the Mitsubishi protocol.

Please check the KEYENCE manual for the compatibility between Mitsubishi devices and KEYENCE
devices.
An example with the KEYENCE PLC KV-5000 is listed below.

Device Name

KEYENCE device

Mitsubishi devices

Relay

R000 00 - R999 15

X(Y)0000 - X(Y)3E7F

Internal auxiliary relay

MR000 00 - MR999 15

M00000 - M15999

Latch relay

LR000 00 - LR999 15

L00000 - L15999

Data memory

DM00000 - DM65534

D00000 - D65534

Extended data memory

EM00000 - EM65534

D100000 - D165534

File register

FM00000 - FM32767

R00000 - R32767

ZF00000 - ZF131071

ZR00000 - ZR131071

M2M Gateway

PLC

KEYENCE KV-5000

IP address : 10.1.1.150

Subnet mask : 255.

０

.

０

.

０

Communication (Connection) port : 5100

* Ethernet port of the CPU Unit is used

IP address : 10.1.1.101
Subnet mask : 255.

０

.

０

.

０

Ethernet connection

MC protocol (Mitsubishi protocol)
Communication data cord : Binary

Device : DM1000 - DM1009
D1000-D1009 (Mitsubishi)
Access cycle : 1 sec

Device : LR10 00 - LR10 09
L160 - L169 (Mitsubishi)
Access cycle : 500 ms.

«
...
50
51
52
53
54
...
»

Содержание CONPROSYS M2M Series








































































































Отзывы:

Нет отзывов