Contec CONPROSYS M2M Series Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 103

Contec CONPROSYS M2M Series Скачать руководство пользователя страница 62

—

PLC Communication Settings

—

M2M Gateway PLC Communication Settings

—

62

—

8.

Modbus/TCP(Ethernet) Connection

The following is a setting example for communication with Modbus/TCP support device.
This example describes how to install the Modbus simulator software on the viewing terminal for
checking the connection.
See below for the configuration example regarding communication conditions.

1.

Terminal Setting

In this setting example, the Modbus simulator "mod_Rssim.exe" by SourceForge is installed on the viewing

terminal for the operation check. This section describes how to install and run the Modbus simulator.



Modbus Simulator Installation Procedure

1.

Access URL listed below and download the simulator software.

URL: https://sourceforge.net/projects/modrssim/files/latest/download

*

The listed URL is subject to change in the future. If that is a case, search "mod_Rssim.exe" on the search site.

2.

Click the "Download" to download .exe file, and save the file to your folder.
* The installer will not be executed.

3.

Double-click .exe file to start the simulation software.

- M2M Gateway

-Viewing and simulator terminal

IP address : 10.1.1.101
Subnet mask : 255.0.0.0

Ethernet connection

Modbus/TCP

Device type : HoldingResister
Access range : 03E9h - 03F2h
Access cycle : 1 sec

Device type : Coil
Access range : 03E9h - 03F2h
Access cycle : 500 ms.

IP address :1

０

.1.1.200

Subnet mask : 255.0.0.0
Communication (Connection) port : 502
*Check the port number of your device

Modbus

Simulator

«
...
60
61
62
63
64
...
»

Содержание CONPROSYS M2M Series








































































































Отзывы:

Нет отзывов