Contec CNT-3204MT-LPE Скачать руководство пользователя страница 53

Страница: 53 / 79

4. Functions

CNT-3204MT-LPE

Obtaining the count value

There are two modes for obtaining the count value. One is the

counter mode

to directly read the count

value without using bus mastering and the other is the

sampling mode

to sample the count value

periodically using bus mastering.

This product is capable of bus mastering, enabling periodical sampling of the count value using the

internal or external clock signal.

Figure 4.8. Counter mode and sampling mode

Counter mode

In the counter mode, the board starts the counter after setting counter operation conditions and performs

counter operations such as reading the count value and status.

In addition, this mode allows the board to preset, zero-clear, start/stop the counter at the rising or falling

edge of the control input signal. A one-shop pulse can be output to the control input signal at an

occurrence of a count match or error.

Figure 4.9. Timing chart (Counter mode)

Is a sampling used?

Bus mastering is not used.

Only counter start/stop is used.

Sampling start/stop cannot be used.

Counter mode

Bus mastering is used.

Both of counter start/stop and sampling start/stop are used.

Counting and sampling can be performed synchronously

by specifying sampling start/stop as the counter start/stop condition

Sampling mode

Yes

Pulse input signal

Sampling clock

Count value

Nothing

Sampling value

Nothing

Counter start

Counter stop

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды