Contec CNT-3204MT-LPE Скачать руководство пользователя

Страница: 74 / 79

6. About Hardware

CNT-3204MT-LPE

About Hardware

This chapter provides hardware specifications and hardware-related supplementary information.

For detailed technical information

For further detailed technical information (“Technical Reference” including the information such as an

I/O map, configuration register, etc.), visit the Contec's web site (http://www.contec.com/support/) to

call for it.

Hardware specifications

Tables 6.1 list the hardware specifications of the board.

Table 6.1. Specifications < 1 / 3 >

Item

Specifications

Input*1

Counter

Channel count

4 channels

Count system

Up/down counting

(2-phase/Single-phase/Single-phase Input with Gate Control Attached)

Max. count

FFFFFFFFh(binary data, 32Bit)

Input type

Unisolated LVTTL level input

Input signal

Phase-A/UP 1 x 4 channels
Phase-B/DOWN 1 x 4 channels

Phase-Z/CLR 1 x 4 channels

Response frequency

10MHz 50% duty

Digital filter

0.1µsec - 1.6384msec or not used
(can be independently set for each channel.)

Timer

1msec - 6553msec 1msec unit

Counter start trigger

Software/External start input/Sampling start trigger

Counter stop trigger

Software/External stop input/Sampling stop trigger

Sampling

Sampling start trigger

Software/External start input/Count match

Sampling stop trigger

Software/External stop input/Specification number/Bus master transfer

error/Count match

Sampling clock

Sampling timer/External clock input

Sampling timer

50nsec - 107sec 25nsec unit (can not be independently set for each
channel.)

External sampling start signal Unisolated LVTTL level input (Select Rise or Fall)
External sampling stop signal Unisolated LVTTL level input (Select Rise or Fall)
External sampling clock signal Unisolated LVTTL level input (Fall)
Response frequency

10MHz 50% duty

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды