Contec CNT-3204MT-LPE Скачать руководство пользователя страница 66

Страница: 66 / 79

4. Functions

CNT-3204MT-LPE

Sampling output signal

The start, stop, or clock signals used to control sampling on this product can be output from the
interface connector.

Sampling start output signal

This outputs the sampling start trigger as a one-shot pulse signal (100nsec) with negative logic polarity.

The logic polarity and pulse width cannot be modified.

Sampling stop output signal

This outputs the sampling stop trigger as a one-shot pulse signal (100nsec) with negative logic polarity.
The logic polarity and pulse width cannot be modified.

Sampling clock output signal

This outputs the sampling clock trigger as a one-shot pulse signal (100nsec) with negative logic

polarity.
The logic polarity and pulse width cannot be modified.

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды