Contec CNT-3204MT-LPE Скачать руководство пользователя

Страница: 65 / 79

4. Functions

CNT-3204MT-LPE

Abnormal input error

An abnormal input error occurs when the counter input signal changes on the A and B phases

simultaneously. Notification of the error is via a status (latch/clear), interrupt, or external output (one-

shot pulse). If the digital filter is enabled, an abnormal input error occurs when both the A and B phases

change during one period of the digital filter source clock. When the filter is disabled, an abnormal input

error occurs when both the A and B phases change during one period of the board 's 40MHz (25nsec)
reference clock.

A possible cause of the abnormal input error is as follows.

When the phase difference between phases-A and B is shorter than one digital filter source clock

cycle (25 nsec with no filter set)

Noise is generated.

Figure 4.17. Abnormal input error

Phase-A input

Phase-B input

An abnormal input error is reported if phases-A and B

change in level during the filter source clock cycle.

No abnormal input error is reported when

the phase difference is longer than the

filter source clock cycle.

Filter source clock

Phase-A input

Phase-B input

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды