Contec CNT-3204MT-LPE Скачать руководство пользователя страница 14

Страница: 14 / 79

1. Before Using the Product

CNT-3204MT-LPE

Environment

Use this product in the following environment. If used in an unauthorized environment, the board may
overheat, malfunction, or cause a failure.

Operating temperature

0 - 50

Operating humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Inspection

Inspect the product periodically as follows to use it safely.

Storage

When storing this product, keep it in its original packing form.

(1) Put the board in the storage bag.

(2) Wrap it in the packing material, and then put it in the box.

(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity.

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

- Check that the bus connector

of the board and its cable have

been plugged correctly.

- Check that the board has

no dust or foreign matter adhering.

- The gold-plated leads of the bus connector

have no stain or corrosion.

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды