Contec CNT-3204MT-LPE Скачать руководство пользователя страница 22

Страница: 22 / 79

2. Setup

CNT-3204MT-LPE

Plugging the Board

(1) Before plugging the board, shut down the system, unplug the power code of your PC.

(2) Remove the cover from the PC so that the board can be mounted.

(3) Plug the board into an extension slot.

(4) Attach the board bracket to the PC.

(5) Put the cover back into place.

Do not touch the board's metal plated terminals (edge connector) with your hands.

Otherwise, the board may malfunction, overheat, or cause a failure.
If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.

Do not install or remove the board to or from the slot while the computer's or extension unit’s

power is turned on.

Otherwise, the board may malfunction, overheat, or cause a failure.

Be sure that the personal computer or the I/O extension unit power is turned off.

Make sure that your PC or extension unit can supply ample power to all the boards installed.

Insufficiently energized boards could malfunction, overheat, or cause a failure.

CAUTION

Содержание CNT-3204MT-LPE
















































































Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды

Contec CNT-3204MT-LPE, Руководство пользователя

Результаты поиска

Содержание CNT-3204MT-LPE

Отзывы:

Похожие инструкции для CNT-3204MT-LPE

Бренды по названию

Популярные бренды