background image

E

N

G

L

IS

H

Conergy TS

Owner & Installation Manual

Gas (AES) Installation Instructions

 

Note

Important note:

|
|
|

|
|

A means for disconnection (eg isolator) must be included in the fixed wiring to the solar water 
heater in accordance with the wiring rules. 
Final electrical connection at the solar water heater is as follows:

Earth - connected to the earthing stud marked with the earth symbol;
Active - connected to the terminal block position marked A or Active;
Neutral - connected to the terminal block position marked N or Neutral.

Do  not  turn  on  the  power  supply  until  the  solar  water  heater  has  been  filled  with  water  and 
pressurised.    There  is  a  risk  of  damage  to  the  system  if  the  installation  sequence  is  not 
followed.

|

  Installation Instructions

Electrical Circuit Diagram

Electrical Connection for Gas AES Systems
For  models  using  a  gas  AES  system  the  electrician  is  required  to  install  a  domestic  electrical 
outlet socket adjacent to the gas heater location. The gas heater requires a 220-240 volt 50 Hz 
powersupply and is rated at 0.47 amperes.

All gas work must comply with local regulations including AS5701/AG601 and AS/NZ 3500.4
All gas work must be conducted by a suitability licensed gas fitter.
Installation  of  the  gas  heater  must  be  installed  in  accordance  with  the  installation  instructions 
supplied with it.
Conergy systems only use approved Gas Heaters.
Particular attention must be given to the gas supply system to ensure the there is a sufficient gas 
supply available to the gas heater when operating at full output burner rate.

Approved Gas Heater Models
Gas heater models used with Conergy solar water heater systems must be certified to all local 
requirements, be automatic ignition and have full flame modulation.

Gas heaters other than this type must not be used with a Conergy solar water heater. Particularly 
fixed pilot and fixed flame models must not be used under any circumstance. 

Please refer to your local distributor for information on approved gas heater model.

5.13.2

5.13.3

5.14.1

5.14

Содержание TS





































Отзывы: