Conergy TS Скачать руководство пользователя страница 34

E

N

G

L

IS

H

Conergy TS

Owner & Installation Manual

The  Conergy  Solar  hot  water  system  that  you  have  purchased  comes  with  a  comprehensive  5  year  parts  and  labour 

warrantly. 

The terms of the Warranty and Guarantee are set out below.

1.

2.

3.

4.

5.

6

Your solar hot water system and its components are covered by a 5 year warranty against defective factory parts or 

workmanship from the date your hot water unit or solar collector is installed. If the date of installation is unknown, the 

warranty commences 1 month after the date of manufacture (which can be found on the serial plate on the hot water unit 

and solar collector).

This warranty is for normal use of the solar hot water system and covers the repair and/or replacement of any failed 

component in the hot water unit and solar collector or where necessary, the hot water unit and solar collector itself. Under 

this warranty Conergy will repair or replace the component or hot water unit or solar collector free of charge (except 

for certain transport or travelling time costs which may be payable by the owner under clause 9 below). The decision to 

repair or replace the component or hot water unit or solar collector will be entirely at the discretion of Conergy.

The  warranty  only  applies  to  defects  in  the  hot  water  unit  and  solar  collector  which  have  arisen  solely  due  to  faulty 

materials or workmanship.

Installation of your Conergy solar hot water system is not covered under this product / manufacturers warranty and in 

cases of installation failure please contact your original installation service provider.

5 Year Guarantee

If any component of the system fails during the initial 5 year warranty period Conergy will replace the failed components 

free of charge. (except for certain transport or travelling time costs which may be payable by the owner under clause 9 

below).

Scope of Warranty and Guarantee

The  warranty  and  replacement  guarantee  do  not  apply  to  any  defects  or  damage  not  due  to  faulty  factory  parts  or 

workmanship, installation, including but not limited to defects or damage caused by or resulting from:

6.1 

6.2

6.3

6.4

6.5

6.6

6.7 

6.8

6.9

   Warranty

Accidental damage, abuse, misuse, maltreatment, abnormal stress or strain, harsh or adverse water conditions, 

contamination  or  corrosion  from  particles  in  the  water  supply,  excessive  water  pressure,  over  temperature  or 

neglect of any kind to the hot water unit and solar collector or their components.

Alteration or repair of the hot water unit or solar collector other than by an approved Conergy agent or a technician 

of a gas or electricity utility approved by Conergy.

Attachment of any parts or accessories other than those manufactured or approved by Conergy.

Faulty  or  improper  installation  of  the  hot  water  unit  or  solar  collector,  including  installation  otherwise  than  in 

accordance with the instructions contained in the Owner’s Manual and Installation Manual supplied by Conergy.

Collector glass is not covered by this warranty.

Where cold water temperature & pressure relief valve, expansion valve, check valve and strainer is not fitted in 

areas where mains pressure is likely to exceed 550 kPa.

Where a closed circuit is not filled with the correct concentration of ST-5 heat transfer fluid in accordance with 

instructions.

In case of overpressure of closed circuit system beyond the 300kPa maximum working pressure.

Where closed circuit has had water addition not in accordance with water quality specifications; and

  Warranty

Содержание TS





































Отзывы: