manualshive.com logo in svg

Conergy TS, Инструкция для владельца и по установке

Поделиться
Скачать
Conergy TS Скачать руководство пользователя страница 14

E

N

G

L

IS

H

Conergy TS

Owner & Installation Manual

5.5

5.6

|

Supplementary Heat Sources

If a supplementary heat source is connected to the storage tank the maximum energy input can be 
not more that 10 kW including the electrical element. Where greater input is required, a pressure and 
temperature relief valve with a higher kW rating is to be fitted to the storage tank.

Where  stove  coils  are  used  for  supplementary  heating  the  water  must  be  connected  in  an  open 
vented  manner.  Refer  to  Australian  Standard  AS3500  for  more  details  on  acceptable  connection 
solutions.

Any supplementary heat source must be limited such that the maximum tank temperature is 80 °C.

For the interconnecting details e.g. pipe work of your specific model/configurations please check the 
assembly drawings in the following pages.

Common installation procedure

The roof system must be carefully inspected to ensure it can support the systems weight once it is 
filled with water. Particular care must be taken where the front foot of the storage tank is located. 
Typically the tank front foot should be located over a tile batten, purlin or similar for maximum 
strength. If the roof can not support the load, additional bracing must be installed before the solar 
water heater is installed.

Determining mounting location
The starting point for the installation is the storage tank front foot. The storage tanks front foot 
must be located over a tile batten or purlin for maximum strength. The batten or purlin selected 
must be located at least 2.4 metres up from the roof’s lower edge and 1 metres down from the 
roof’s ridge line so that the ridge caps are not disturbed.

1.

2. 

5.6.1

Place the tank into position with its front foot centrally over the selected tile batten. The tank 
should be installed 

after the collectors are installed. The tank centre should be installed over 

rafters/trusses evenly so as to spread the tank weight over an even area of the roof.

Measure down the roof from the right side front edge of the front foot a distance of 2030 mm 
and make a mark on the roof tile. This position (Point 2 of mounting location) will be the bottom 
edge of the collector mounting rail.

  Installation Instructions

Содержание TS





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды