Conductix-Wampfler MultiLine 0835 Скачать руководство пользователя страница 43

Страница: 43 / 81

Mounting Instruction

Conductor rail system

MultiLine 0835

MAL0835-0001c-EN
www.conductix.com

translated document

page 43 of 81

Installing end segment with power feed (anchor point)

Requirement:

DANGER!

Risk of death by electrocution!

Touching the connecting cable can result in death and severe injury from electric shock.

→

Disconnect the power supply for the conductor rail by switching it off at the

main switch

→

If there is no main switch, disconnect the end of the connecting cable from the power

source or do not yet connect the cable that is not going to be connected to the

conductor rail's power terminal.

→

Protect the power supply from being switched back on

→

Make sure the system is disconnected by measuring the current

→

Ground and then short-circuit parts of the system that have been disconnected from

the power supply

→

Cover or block adjacent components that are still live

→

Attach a sign saying "Risk of death by electrocution" with the relevant hazard symbol

in all areas with live components (power feed)

→

Properly crimp the crimp-type sockets (1) on the
connecting cables (2) with the Klauke K2 crimping
tool.

Fig. 24: Power terminals with crimp-type socket (1),

connecting cable (2)

Содержание MultiLine 0835


















































































Результаты поиска

Содержание MultiLine 0835

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler MultiLine 0835, Инструкция по монтажу

Результаты поиска

Содержание MultiLine 0835

Отзывы:

Бренды по названию

Популярные бренды