manualshive.com logo in svg

Conductix-Wampfler MultiLine 0835, Инструкция по монтажу

Поделиться
Скачать
Conductix-Wampfler MultiLine 0835 Скачать руководство пользователя страница 30

Mounting Instruction 

 

Conductor rail system 

MultiLine 0835 

 

 

MAL0835-0001c-EN 
www.conductix.com 

translated document 

page 30 of 81 

Required protective equipment: 

 

 

CAUTION! 

Risk of injury from punctures and cuts!

 

The packaging material may contain sharp objects such as nails and wood splinters that 

can cause injury to limbs. 

→

 

Wear protective gloves 

→

 

Wear safety shoes 

 

5.1.2

 

Transporting the packed parts 

Packages must be transported under the following conditions: 

 

Keep dry and do not expose to dust 

 

Do not expose to aggressive media 

 

Protect from direct sunlight 

 

Avoid mechanical vibrations 

 

Transport temperature: -25 °C to +55 °C 

 

Relative humidity: max. 85% 

5.1.3

 

Transport inspection 

The individually packaged parts have been packed in accordance with the anticipated transport conditions. Check the delivery for 
completeness and transport damage immediately on receipt. 
If transport damage is externally visible, proceed as follows: 

 

 

Do not accept delivery, or accept it only with reservations 

 

Record the scope of the damage on the transport documents or on the transporter's delivery note 

 

File a complaint 

 

 

CAUTION!

 

All damage must be reported immediately following detection. Damage compensation claims may only 
be made within the applicable claim periods. 

5.2

 

Storing the  packed parts 

 

 

CAUTION!

 

 
In some cases, there may be instructions for storage on the packed parts that go beyond the 
requirements listed here. These must be correspondingly observed. 

Packaged parts must be stored under the following conditions: 

 

Do not store outdoors 

 

Store in a dry, dust-free place 

 

Do not expose to aggressive media 

 

Protect from direct sunlight 

Содержание MultiLine 0835


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды