Condair GC 130 Скачать руководство пользователя страница 69

Страница: 69 / 72

Performance and Operating Data

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

Gas Operating Pressure:

Natural gas:

H, E, E(S)

G20

1.69-2.49 kPa

L, ELL

G25

1.99-2.99 kPa

G25.1

1.99-2.99 kPa

G27

1.74-2.29 kPa

G2.350

1.05-1.59 kPa

Propane:

G31

2.49-5.73 kPa

Levels in Flue Products:

Gas Type:

at Maximum Rate

at Minimum Rate

G20

9.5 ± 0.2%

8.5 ± 0.2%

G25

G25.1

G27

G2.350

G31

10.4 ± 0.2%

9.5 ± 0.2%

Water Supply:

Water pressure (regulated)

3.0-8.0 bar, 207-550 kPa

Flow rate

10 L/min for GS 23-130 , 20 L/min for GS 195-260

Water temperature

1-15 °C recommended; maximum 25 °C

Water quality

Cold potable water filtered to 5 μm, hardness of 0-256 ppm, pH level between 5-8

and chloride 0-50 ppm.

Drain Water:

Drain water temperature

60 °C maximum

Drainage capacity

20 L/min

Power:

230 V/1~50 Hz

Pn max. in kW

In max. in A

Cable cross

section (mm

)

Fuse "F1" in A

Slow acting (aM)

GS 23-CS

0.23

1.0

1.5

GS 45-CS

0.23

1.0

1.5

GS 65-CS

0.35

1.5

GS 90-CS

0.32

1.4

1.5

GS130-CS

0.53

2.3

1.5

GS 195-CS

0.72

3.1

1.5

GS 260-CS

0.92

4.0

1.5

Содержание GC 130









































































Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды

Condair GC 130, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды