Condair GC 130 Скачать руководство пользователя страница 27

Страница: 27 / 72

Operator Interface

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

RH Alerts Tab
Note

: This tab appears only if

Control Mode

is set to "RH P" or "RH PI".

–

RH Alerts:

allows you to enable or disable the alert function that

warns if sensed humidity is too high or too low.
Options:

– enables the function.

Off

– disables the function.

Factory setting:

Off

Note:

The following settings are only available if the RH Alerts func

tion is enabled.

–

RH High:

allows you to set the upper limit value of the humidity

sensor signal. The RH High warning message is triggered when the

signal value exceeds this limit.
Setting range:

20-95%

Factory setting:

75%

–

RH Low:

allows you to set the lower limit value of the humidity

sensor signal. The RH Low warning message is triggered when the

signal value drops below this limit.
Setting range:

20-95%

Factory setting:

20%

–

Sensor Min:

allows you to set the minimum signal value of the

humidity sensor. If the signal value drops below this setting, the

sensor is assumed to be damaged or disconnected. The RH Signal

warning message is triggered when the signal value drops below

this limit, and humidification stops.
Setting range:

1-10%

Factory setting:

Содержание GC 130









































































Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды

Condair GC 130, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды