Comnet CWGE26FX2TX24MSPOE Скачать руководство пользователя

Страница: 100 / 138

INS_CWGE26FX2TX24MSPOE_REV– 5 Mar 2014 PAGE 100

INSTALLATION AND OPERATION MANUAL

CWGE26FX2TX24MSPOE

TECH SUPPORT: 1.888.678.9427

Event Selection

SYSLOG and SMTP are the two warning methods that supported by the system. Check the
corresponding box to enable system event warning method you wish to choose. Please note that
the checkbox cannot be checked when SYSLOG or SMTP is disabled.

System Warning – Event Selection interface

The following table describes the labels in this screen.

Label

Description

System Cold Start

Alert when system restart

Power Status

Alert when a power up or down

SNMP Authentication Failure

Alert when SNMP authentication failure.

Redundant Ring Topology Change Alert when C-Ring topology changes.
Port Event
SYSLOG = event

› Disable
› Link Up
› Link Down
› Link Up & Link Down

Save

Click to save the configurations.

Reset

Click to reset the configurations.

Содержание CWGE26FX2TX24MSPOE











































































































































Результаты поиска

Содержание CWGE26FX2TX24MSPOE

Отзывы:

Похожие инструкции для CWGE26FX2TX24MSPOE

Бренды по названию

Популярные бренды

Comnet CWGE26FX2TX24MSPOE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE26FX2TX24MSPOE

Отзывы:

Похожие инструкции для CWGE26FX2TX24MSPOE

Бренды по названию

Популярные бренды