Comnet CWGE26FX2TX24MSPOE Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 138

background image

INS_CWGE26FX2TX24MSPOE_REV– 5 Mar 2014 PAGE 106

INSTALLATION AND OPERATION MANUAL

CWGE26FX2TX24MSPOE

TECH SUPPORT: 1.888.678.9427

Short frames are frames that are smaller than 64 bytes.

Long frames are frames that are longer than the configured maximum frame length for this port.

Port Monitoring

Configure port Mirroring on this page.

To debug network problems, selected traffic can be copied, or mirrored, to a mirror port where a
frame analyzer can be attached to analyze the frame flow.

The traffic to be copied to the mirror port is selected as follows:

All frames received on a given port (also known as ingress or source mirroring).

All frames transmitted on a given port (also known as egress or destination mirroring).

Port to mirror also known as the mirror port. Frames from ports that have either source (rx) or
destination (tx) mirroring enabled are mirrored to this port. Disabled disables mirroring.

Label

Description

Port

The logical port for the settings contained in the same row.

Mode

Select mirror mode.
Rx only : Frames received at this port are mirrored to the mirror port. Frames
transmitted are not mirrored.
Tx only :Frames transmitted from this port are mirrored to the mirror port. Frames
received are not mirrored.
Disabled : Neither frames transmitted nor frames received are mirrored.
Enabled : Frames received and frames transmitted are mirrored to the mirror port.
Note: For a given port, a frame is only transmitted once. It is therefore not possible to
mirror Tx frames for the mirror port. Because of this, mode for the selected mirror port
is limited to Disabled or Rx only.

«
...
104
105
106
107
108
...
»

Содержание CWGE26FX2TX24MSPOE











































































































































Отзывы:

Нет отзывов

Похожие инструкции для CWGE26FX2TX24MSPOE

ePowerSwitch 8M+R2

Бренд: Neol Страницы: 74

Бренд: LONG-JOIN Страницы: 2

GenReady Series 005448-2

Бренд: Generac Power Systems Страницы: 4

SmartSwitch 2500

Бренд: Cabletron Systems Страницы: 402

Бренд: DeLOCK Страницы: 8

Бренд: G-Lab Страницы: 12

Бренд: Manhattan Страницы: 2

Mini Hub 5 port

Бренд: Sandberg Страницы: 12

SOLO Airliner RS

Бренд: Virtualfly Страницы: 32

VNLW-P-1001-MV-N-W

Бренд: Greengate Страницы: 2

Бренд: WaveSplitter Страницы: 35

Бренд: Southern States Страницы: 32

Бренд: Intelix Страницы: 40

Бренд: Maretron Страницы: 9

Бренд: Rose electronics Страницы: 68

Бренд: Channel Vision Страницы: 2

Elinx EIRP305-T

Бренд: B&B Electronics Страницы: 2

Бренд: Ross Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды