manualshive.com logo in svg

Comnet CWGE26FX2TX24MSPOE, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE26FX2TX24MSPOE Скачать руководство пользователя страница 114

INS_CWGE26FX2TX24MSPOE_REV–     5 Mar 2014     PAGE 114

INSTALLATION AND OPERATION MANUAL 

CWGE26FX2TX24MSPOE

TECH SUPPORT: 1.888.678.9427

Power 
Management 
Mode

There are 2 modes for configuring when to shut down the ports: 
1. Actual Consumption: In this mode the ports are shut down when the actual power 
consumption for all ports exceeds the amount of power that the power supply can 
deliver or if the actual power consumption for a given port exceeds the reserved power 
for that port. The ports are shut down according to the ports priority. If two ports have 
the same priority the port with the highest port number is shut down. 
2. Reserved Power: In this mode the ports are shut down when total reserved powered 
exceeds the amount of power that the power supply can deliver. In this mode the port 
power is not turned on if the PD requests more power than available from the power 
supply.

Primary and 
Backup Power 
Source

Some switches support having two PoE power supplies. One is used as primary power 
source, and one as backup power source. If the switch doesn’t support backup power 
supply only the primary power supply settings will be shown. In case that the primary 
power source fails the backup power source will take over. For being able to determine 
the amount of power the PD may use, it must be defined what amount of power the 
primary and backup power sources can deliver. 
Valid values are in the range 0 to 2000 Watts.

Port

This is the logical port number for this row. 
Ports that are not PoE-capable are grayed out and thus impossible to configure PoE for.

PoE Mode

The PoE Mode represents the PoE operating mode for the port. 
Disabled: PoE disabled for the port. 
PoE : Enables PoE IEEE 802.3af (Class 4 PDs limited to 15.4W) 
PoE+ : Enables PoE+ IEEE 802.3at (Class 4 PDs limited to 30W)

Priority

The Priority represents the ports priority. There are three levels of power priority 
named Low, High and Critical. 
The priority is used in the case where the remote devices requires more power than the 
power supply can deliver. In this case the port with the lowest priority will be turn off 
starting from the port with the highest port number.

Maximum Power The Maximum Power value contains a numerical value that indicates the maximum 

power in watts that can be delivered to a remote device.(The maximum allowed value 
is 30 W.)

Содержание CWGE26FX2TX24MSPOE











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды