manualshive.com logo in svg

Comnet CWGE26FX2TX24MSPOE, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE26FX2TX24MSPOE Скачать руководство пользователя страница 113

 INS_CWGE26FX2TX24MSPOE_REV–     5 Mar 2014     PAGE 113

INSTALLATION AND OPERATION MANUAL 

CWGE26FX2TX24MSPOE

TECH SUPPORT: 1.888.678.9427

PoE Configuration

PoE is an acronym for Power Over Ethernet. Power Over Ethernet is used to transmit electrical 
power, to remote devices over standard Ethernet cable. It could for example be used for powering 
IP telephones, wireless LAN access points and other equipment, where it would be difficult or 
expensive to connect the equipment to main power supply.

Label

Description

Reserved Power 
determined by

There are three modes for configuring how the ports/PDs may reserve power. 
1. Allocated mode: In this mode the user allocates the amount of power that each 
port may reserve. The allocated/reserved power for each port/PD is specified in the 
Maximum Power fields. 
2. Class mode: In this mode each port automatically determines how much power to 
reserve according to the class the connected PD belongs to, and reserves the power 
accordingly. Four different port classes exist and one for 4, 7, 15.4 or 30 Watts. 
In this mode the Maximum Power fields have no effect. 
3. LLDP-MED mode: This mode is similar to the Class mode expect that each port 
determine the amount power it reserves by exchanging PoE information using the LLDP 
protocol and reserves power accordingly. If no LLDP information is available for a port, 
the port will reserve power using the class mode 
In this mode the Maximum Power fields have no effect 
For all modes: If a port uses more power than the reserved power for the port, the port 
is shut down.

Содержание CWGE26FX2TX24MSPOE











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды